Omni Bead Ruptor 96 Benutzerhandbuch Seite 3

Data herein has been verified and validated. It is believed adequate for the intended use of the instrument.
If the instrument or procedures are used for purposes over and above the capabilities specified herein,
confirmation of the validity and suitability should be obtained; otherwise Omni International does not
guarantee results and assumes no obligation or liability. This publication is not a license to operate under, or
a recommendation to infringe upon, any process patents.
This product is warranted to be free from defects in material and workmanship for a period of ONE YEAR
from the date of delivery. Omni International will repair or replace and return free of charge any part which
is returned to its factory within said period, transportation prepaid by user, and which is found upon
inspection to have been defective in materials or workmanship. This warranty does not include normal wear
from use; it does not apply to any instrument or parts which have been altered by anyone other than an em-
ployee of Omni International nor to any instrument which has been damaged through accident, negligence,
failure to follow operating instructions, the use of electric currents or circuits other than those specified on
the plate affixed to the instrument, misuse, or abuse. Omni International reserves the right to change, alter,
modify, or improve any of its instruments without any obligation whatever to make corresponding changes
to any instrument previously sold or shipped.
THE FORGOING OBLIGATION IS IN LIEU OF ALL OBLIGATIONS AND LIABILITIES INCLUDING NEGLIGENCE AND
ALL WARRANTIES OF MERCHANTABILITY OR OTHERWISE, EXPRESSED OR IMPLIED IN FACT OR BY LAW, AND
STATE OUR ENTIRE AND EXCLUSIVE LIABILITY AND BUYERS EXCLUSIVE REMEDY FOR ANY CLAIM OF DAMAG-
ES IN CONNECTION WITH THE SALE OR FURNISHING OF GOODS OR PARTS, THEIR DESIGN, SUITABILITY FOR
USE, INSTALLATION, OR OPERATION. OMNI INTERNATIONAL WILL IN NO EVENT BE LIABLE FOR ANY SPECIAL
OR CONSEQUENTIAL DAMAGES WHATSOEVER, AND THEIR LIABILITY UNDER NO CIRCUMSTANCES WILL
EXCEED THE CONTRACT PRICE FOR THE GOODS FOR WHICH LIABILITY IS CLAIMED.
This product has been engineered for safety; however, basic safety precautions and common sense must
always be demonstrated when using any electrical product.
- DO NOT attempt to modify any part of this product.
- DO NOT allow the machine to be submerged in any liquid.
- DO NOT use in any setting other than an indoor laboratory.
- DO NOT plug power cord into an incorrect outlet or subject it to an incorrect voltage.
- Use this product only for its intended purpose.
- DO NOT use attachments not recommended by the manufacturer.
- DO NOT operate the product if it is damaged in any way.
- Keep this product away from heated surfaces.
- DO NOT modify the plug or cord that is provided. If the plug will not fit the outlet, have the proper outlet
installed by a qualified electrician.
- DO NOT operate the product with the safety ground disconnected.
WARNING: The processing chamber of the Bead Ruptor 96 is enclosed by a strong covering lid. Start-
ing of the machine is possible only with the lid closed. If the lid is open, message "LID" appears on the
display, when the START/STOP key is pressed. When message "LID" appears on display, the lid must
be closed and the error message cleared by pressing the START/STOP key. The instrument can then be
started by pressing the START/STOP key again. If the lid is opened during operation, the machine stops
rapidly and message "Er3" appears on display. When message "Er3" appears on display, the machine
cannot be restarted by pressing the START/STOP key. The main POWER switch must be turned to OFF
and then ON again, to clear the message before instrument operation can proceed.
MILLING JAR FILL REQUIREMENTS
WARNING: The sample quantity must not be less than 25% of the milling jar capacity. The milling balls
may otherwise damage the milling jars. The milling jars and milling balls must be the same material.
Otherwise the milling jar could be damaged.
WARNING: The instrument must be balanced prior to operation. Do not operate the instrument with only
one milling jar or one well plate adapter installed in a single milling jar holder. Both milling jar holders
must have either a milling jar (filled with equivalent mass) or well plate adapters. If not balanced dam-
age to the lid is possible.