Maintenance - Makita RP0910 Bedienungsanleitung

Fig.8
NOTE:
Make sure that the dust guide is installed properly.
•
Moving the tool forward too fast may cause a poor
•
quality of cut, or damage to the bit or motor.
Moving the tool forward too slowly may burn and
mar the cut. The proper feed rate will depend on
the bit size, the kind of workpiece and depth of cut.
Before beginning the cut on the actual workpiece, it
is advisable to make a sample cut on a piece of
scrap lumber. This will show exactly how the cut
will look as well as enable you to check
dimensions.
When using the straight guide, be sure to install it
•
on the right side in the feed direction. This will help
to keep it flush with the side of the workpiece.
Fig.9
Straight guide
Fig.10
The straight guide is effectively used for straight cuts
when chamfering or grooving.
To install the straight guide, insert the guide bars into the
holes in the tool base. Adjust the distance between the
bit and the straight guide. At the desired distance,
tighten the lock screw to secure the straight guide in
place.
Fig.11
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
If the distance between the side of the workpiece and
the cutting position is too wide for the straight guide, or if
the side of the workpiece is not straight, the straight
guide cannot be used. In this case, firmly clamp a
straight board to the workpiece and use it as a guide
against the router base. Feed the tool in the direction of
the arrow.
Fig.12
Templet guide (Accessory)
Fig.13
The templet guide provides a sleeve through which the
bit passes, allowing use of the tool with templet patterns.
To install the templet guide, loosen the screws on the
tool base, insert the templet guide and then tighten the
screws.
Fig.14
Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.
Fig.15
NOTE:
The workpiece will be cut a slightly different size
•
from the templet. Allow for the distance (X)
between the bit and the outside of the templet
guide. The distance (X) can be calculated by using
the following equation:
Distance (X) = (outside diameter of the templet
guide - bit diameter) / 2
Connecting to Makita vacuum cleaner
Fig.16
Cleaner operations can be performed by connecting the
tool to Makita vacuum cleaner.
Insert the nozzle assembly and the dust nozzle
assembly into the tool. Also, the dust nozzle assembly
can be inserted into the tool base directly in accordance
with the operation.
When connecting to Makita vacuum cleaner (Model 407),
an optional hose 28 mm in inner diameter is necessary.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before attempting to perform inspection
or maintenance.
Replacing carbon brushes
Fig.17
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
Fig.18
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
ACCESSORIES
CAUTION:
These accessories
•
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons.
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Straight & groove forming bits
•
Edge forming bits
•
Laminate trimming bits
•
Straight guide
•
Templet guide 25
•
Templet guides
•
Lock nut
•
Collet cone 3/8", 1/4"
•
8
or attachments
Only use accessory or
are