Specified Use; General Safety Instructions; Special Safety Instructions - Metabo GED 125 Originalbetriebsanleitung

Original instructions

1. Specified Use

The extraction hood is designed to be attached to
the original safety guard for Metabo angle grinders
with the name W...8-...; W...9-...; W...10-...; W...11-
...; W...12-...; W...14-..., W...15-....; W...17-.... as of
the year of manufacture 2008. The year of
manufacture (Y) is specified on the machine rating
plate. For example:
99999999
D-72622 Nürtingen
Type
Made in Germany
The extraction hood is designed for surface
grinding with diamond cups, fibre grinding plates
and cling-fit backing plads. (Attach cling-fit backing
pads only to angle grinders without Autobalancer).
The maximum permitted diameter of the
accessories is 125 mm (5").
When working with diamond cups, use an angle
grinder with a rated input power of at least 1400W.
Do not use for abrasive cutting-off operations,
roughing work, sanding, polishing or flap disc work.
Do not machine any metallic materials.
Suitable for the extraction of dusts generated during
surface grinding of mineral materials, wood,
plastics, glassfibre-reinforced plastics, paints and
residue of adhesives.
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (14). We recommend
using an antistatic suction hose Ø 35 mm.
Note: The ring brush may stick when thermoelastic
materials are processed.
The machine must not be used with water.
It is suitable for commercial use in trade and
industry.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
Read the operating instructions supplied with the
installed angle grinder.

2. General Safety Instructions

For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
999 44 12345
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.

3. Special Safety Instructions

3.1 Safety warnings common for grinding,
sanding:
Use
a) This guard is designed for surface grinding.
Read all safety warnings, instructions,
illustrations and specifications provided with
this guard. Failure to follow all instructions listed
below may result in electric shock, fire and/or
serious injury.
b) This guard is not suitable for routing,
polishing, sanding, working with roughing
discs, wire brushes, parting grinder discs or
flap discs. Operations for which the guard was not
designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not
specifically designed and recommended for
this guard and the power tool by the
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
e) The outside diameter and the thickness of
your accessory must correspond to the
dimensions of your guard and your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Prior to each use check if parts are missing,
worn, broken, torn or damaged. Do not use
defective or incomplete guard.
g) Do not use a damaged accessory. Before
use, always check accessories for splinters or
cracks and check grinding wheels for cracks or
signs of severe wear and tear. If a power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by
various operations. The dust mask or respirator
ENGLISH en
7