Peg Perego Skate Gebrauchsanleitung Seite 20

DETACHING THE Skate-SEAT FROM THE Skate CHASSIS
19• Raise the bumper bar to the up position (carrying
handlebar), hold it and pull it upwards (1), detach the
Skate-seat on one side (2) then on the other (3) by
pressing the tabs where the hood attaches.
• IMPORTANT: when the child is seated, this operation
can be carried out only if the Skate seat is in carriage
mode and your child weighs less than 9 kg.
RECLINABLE Skate-SEAT
20• The Skate-seat can be reclined to 3 positions (horizontal,
partially reclined and reclined) either facing parents or the
other way.
• To recline the Skate seat, pull up the handle behind the
backrest and adjust the Skate seat to the position you want.
• Skate carriage seat: the Skate-seat must be fully
horizontal.
• Skate stroller seat: the Skate-seat can be inclined to the
3 positions available.
HEIGHT ADJUSTABLE Skate-SEAT
21• The Skate-seat is height adjustable to 3 positions: To
adjust the height, press the two side buttons on the Skate
chassis and simultaneously move the Skate-seat up or
down until they click into place. To make sure that the
Skate-seat is secured, check the 3 arrows on the Skate
chassis.
LEGREST
22• If the Skate seat is in the carriage position, the leg rest
must stay in the reclined (flat) position. If the Skate seat is
in the stroller seat position, the leg rest can be adjusted to
2 positions (reclined or upright).
23• To adjust it, pull the side adjuster traps and place over the
side pins. Pull the additional loose strap under the stroller
seat and attach it to the Velcro on the bottom of the seat.
BACKREST
24• The backrest can be set in 3 positions: horizontal, partially
raised, and raised.
To adjust the backrest, take the central strap and place
one of the 3 eyelets on the pin behind the backrest.
BUMPER BAR/CARRYING HANDLE
25• To attach it, place the fasteners of the bumper bar on
the Skate-seat side buttons, push the buttons down and
slide the bumper bar into the groves until it snaps in. The
bumper bar can be attached to the Skate-seat in one way
only.
26• To remove it, press the button below the bumper bar and
slide out of the groves.
27• The bumper bar can be opened and closed: to make it
easier for the child to go in and out of the stroller when
he/she is older.
To open it: press the two round buttons simultaneously
and pull the bumper bar outwards.
To close it: follow these steps the other way round.
28• The bumper bar can be adjusted to 2 height positions:
lower position (A) – bumper bar mode – and high
position (B) – carrying handle mode, to carry a child up to
9 kg only when the Skate-seat is used as a carriage.
• To adjust it in height: open the two levers inward, move the
bumper bar up or down and close the two levers again.
HOOD
29• To mount the hood, insert the hood fasteners into the
proper holes of the Skate seat with the snaps to the rear
of the stroller seat, then fasten all 4 snaps on the Skate
seat.
30• To remove it, unsnap the hood from the side Skate seat,
press in the thin black buttons under the grey tabs and
pull the hood off.
31• The hood can also be extended for use in the carriage
mode by unzipping the zipper on the outside of the
hood.
BOOT
32• To place the boot on the Skate seat, fasten the two snaps
at the bottom of the Skate seat and put the elastic strings
onto the two side pins on the bumper bar. The boot
also has side magnets to help secure it to the Skate seat.
When using the boot in the carriage position you can
unzip the boot to allow more room for your children's feet.
RAIN COVER
33• To attach it, zip the rain cover and the hood together (A),
pull the bottom part of the rain cover under the Skate-
seat (B), pass the elastic strings and buttons behind the
locking system of the Skate-seat (C), then button them
up to the rain cover (D).
• The rain cover can be opened while attached to the
Skate-seat due to the elastic strings, but the zipper must
be open.
• If you want to turn the Skate-seat, you do not need to
remove the rain cover as it is attached to the Skate-seat
and not to the Skate chassis.
• Do not use the rain cover in closed environments and
always make sure the child is not too hot.
• Do not place the rain cover near heat sources and be
careful with cigarettes.
• Check that the rain cover does not hinder the correct
functioning of the carriage or stroller.
• Always remove the rain cover before closing your carriage
or stroller.
• Wash with a sponge and soap water, without using
detergents.
5 POINT HARNESS SAFETY BELT
34• Safety belts are stored under the interior Skate-seat
padding in their proper housings.
35• The seat belt is hidden under the interior Skate-seat
padding: From the carriage position to access the safety
belts, you need to unsnap the 4 snaps where the backrest
meets the bottom of the seat. Pull up the seat pad and
pull the shoulder harness out. Next slide the crotch strap
thru the slit in the seat pad. Snap all 4 snaps back down
on the seat pad.
36• To fasten the harness, check that the shoulder straps are
properly inserted in the waist strap, then click together
the buckle of the waist strap and the leg strap. To unfasten
the harness, press on the side of the buckle while pulling
the waist strap upwards.
The new safety belt is easier to wear, thanks to the "snap
open and shut" system. Before attaching the safety belt,
attach the small buckle to the backrest by inserting the
tab into the special holder, as shown in the figure. Next,
fasten the safety belt on your child, and then detach the
belt from the backrest to allow the child more freedom of
movement. The small buckle should be placed below the
child's shoulders. To tighten the waist strap, pull on both
sides in the direction of the arrow (fig_6). To loosen it do
the opposite. The waist strap can be tightened as far as
the safety lock.
FOLDING THE STROLLER/CARRIAGE
• Close the hood, if attached:
• Move the Skate-seat down to the lowest position.
37• If the Skate-seat is attached to the Skate chassis
facing parents, first pull out the safety trigger (1) and
simultaneously recline the Skate-seat by pulling up the
handle behind the backrest (2), then align the seat to the
Skate handlebar assembly (3).
38• If the Skate-seat is attached to the Skate chassis so that
the child can see what's ahead, recline the Skate-seat by
pulling up the handle behind the backrest and align the
seat to the Skate chassis.
39• To close the Skate chassis when it is fully reclined, move
the telescopic handlebar if extended to the lowest
position. Press the folding pedal with a foot. Next pull the
left trigger and then the right trigger.
40• turn the two levers upwards one side then the other;