Product Parts - Peg Perego Skate Gebrauchsanleitung

• Do not add any mattress.
• Leaving your child unattended can be dangerous.
• Do not let other children play near the product if
unattended.
• The product must be prepared and assembled by an adult.
• Do not use this product if it is broken or any part is
missing.
• Always apply the brakes when not moving.
• Apply the brakes during loading and unloading
operations.
• Before use, check that all the locking systems are secured
properly.
• Keep fingers away from the locking systems.
• Pay attention to the child while adjusting the systems
(handlebar, backrest).
• Any load hanging on the handlebar or the handles
can make the stroller/carriage unstable; follow the
manufacturer's instructions for max load capacity.
• Do not place loads over 5 kilos in the basket. Do not place
in the bottle holder weights heavier than stated or hot
drinks. Do not place in the hood pockets (if applicable)
weights over 0.2 Kg.
• Do not use this product near stairs or steps; do not use
near heat sources, open flames or dangerous objects in
the reach of your child's hands.
• Using accessories which do not bear the manufacturer's
approval may be dangerous.
• This product is not suitable for jogging or skating.

product parts

• Check the package contents and contact our Customer
Service for any claim.
• Skate chassis with basket and pump
• 4 wheels with shock absorbers and ball bearings (2 front
lockable swivel wheels - 2 rear wheels with air chamber)
• Bottle holder
• Skate-seat
• Bumper bar
• Hood and cover
• Rain cover
• Standard adapter set for car seat group 0+ "Primo Viaggio
SIP" or "Primo Viaggio tri-fix" Peg Perego.
instructions for use
MOUNTING THE WHEELS
1• Remove the protection caps from the rear wheels. To
mount the rear wheels, insert the pins into their housings
until they click into place.
2• Before fitting the front wheels, make sure that the
indicators on the fastening controls are red. Insert the
pins of the wheels in the appropriate housing, making
sure that the green lines of the wheels match up with
the green lines of the housing. Finally, turn the fastening
controls until the indicators are green.
• IMPORTANT: Check that the wheels are secured by
pulling them.
OPENING the Skate chassis
3• To open the Skate chassis remove the locking levers (fig.
A) from the side pins and push them up until they go
back in.
4• If it is in the closed position (fig. A), rotate the handlebar
by one position (fig. B, open the two levers outwards,
position the handlebar and close the two levers again) to
avoid contact with the centralized locking pedal (fig. C).
5• Hold the Skate chassis down with a foot and raise the
handlebar until it clicks into place.
Check that the chassis is open properly by making sure
that the front of the centralized locking pedal is not red.(
If the red part is visible, continue to pull up the handlebar
until you hear it click and the red is no longer visible on
the centralized locking pedal.
The Skate chassis can also be opened when the Skate-seat
is attached; after opening the Skate chassis, recline the
Skate-seat as needed (see reclining the Skate seat section).
IMPORTANT: Sit the child in the Skate-seat only after
opening the Skate chassis.
CENTRALIZED BRAKE
6• Press the brake lever on the rear wheel unit to set the
brake on the stroller.
Release the lever to release the brake.
FRONT SWIVEL WHEELS
7• To set the front wheels to swivel, lift the stopper up, as
in figure A. To set the wheels in a fixed position, push
the stopper down, as in figure B. When they are turned
around, the wheels automatically fix into place.
REAR INFLATABLE WHEELS
8• A pump is attached to the bottom of the frame in the
rear of the stroller to inflate the rear wheels. Pull out the
cord from the top of the pump and screw it in the figure.
Unscrew the wheel valve cap and screw the cord of the
pump.
• Before using the stroller for the first time you are advised
to inflate the tires to a pressure of 25 psi/1.7 bar.
• IMPORTANT: Do not inflate the wheels too much; max
pressure is stated on the wheel.
HANDLEBAR
• The handlebar of the Skate chassis is telescopic and the
handle grip is height adjustable to 3 positions.
9• To extend the handlebar, pull up the two handlebar
extender hooks simultaneously and place the handlebar
at the height you want it.
10• To adjust in height the handle grip, open the two levers
outwards, place the handle grip in the position you want and
lock the two levers again.
BOTTLE HOLDER
11• The bottle holder can be attached to both sides of the
Skate chassis, To attach it, insert the back of the bottle
holder into the housing provided on the Skate chassis.
BASKET
12• The basket is equipped with adjustable elastic straps to
secure the contents. Before connecting the straps, place
the elastic strings in the suitable position.
REMOVING THE WHEELS
13• To remove the rear wheels from the Skate chassis, pull out
the pin while taking off the wheels.
14• To remove the front wheels from the Skate chassis, turn
the fixing knobs until the indicators are red, then take off
the wheels.
REVERSIBLE Skate-SEAT
• The Skate-seat is reversible, so it can be attached to the
Skate chassis to face parents or let your child see what's
ahead.
15• Skate carriage seat: must be fixed to the Skate chassis so
it faces parents to keep a constant eye on your little baby.
16• Skate stroller seat: can be fixed to the Skate chassis so
the baby can face parents (1) or see what's ahead (2).
ATTACHING THE Skate-SEAT TO THE Skate CHASSIS
17• Before attaching the Skate-seat to the Skate chassis, make
sure both locking systems are at the same height and
rotated to the same position.
18• To attach the seat, insert the legs of the Skate seat into the
holes in the Skate chassis until they click into place.
• IMPORTANT: Make sure the Skate-seat is attached
properly by pulling it upwards.
• IMPORTANT: This operation is required only if the
Skate-seat is in carriage mode and your child weighs
less than 9 kg.