Herunterladen Inhalt Inhalt Diese Seite drucken

COMAC CA30 Betriebsanleitung Seite 11

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
WARNING
GB
Carefully read all the instructions and warnings in the instructions booklet and
keep the booklet for future reference. Failure to carry out all these instructions can
result in potential hazards from the machine. The packaging components (plastic bags,
staples, etc..) can be potentially dangerous and should be kept out of the reach of
children and handicapped persons. After having opened the package, examíne the
contents to make sure that it is intact and in case of missing or defective parts, contact
an authorized dealer or service centre before using the machine, in order to receive the
original parts. Before connecting the machine to the source of electricity, make certain
that the electrícal specifications mentioned on the label on the machine, are the same as
the source of electricity. This machine is designed to be used only as intended: vacuum
cleaning of inert surfaces, and the aspiration of solids and liquids which are not
inflammable or explosive. All other uses are to be considered as improper and
potentially dangerous. Avoid bringing the attachment in use to close proximity of
sensitive organs such as eyes, ears, etc.. Do not leave the machine within reach of
unattended children or handicapped persons. Do not leave the machine connected to
electricity when not in use. Before cleaning or carrying out any maintenance work on the
machine, disconnect it from the source of electricity. Never immerse the machine in
water, and never use the machine to vacuum harsh solvents and liquids and foam-
producing chemicals. Do not bring harsh solvents and liquids into contact with the
machine. The manufacturer cannot be held responsible for any damage to persons,
animals, or objects as a result of incorrect and/or improper use of the machine and due
to the user's failure to carry out all the above instructions and warnings.
TO USE AS DRY VACUUM CLEANER (not to vacuum liquids):
Make sure that the plug is disconnected from the source of electricity (figure 1). Unhook
the tank latches (figure 2), remove the head and ensure that the cloth filter is properly
installed (figure 3). Put the head in its original position again and secure it onto the tank
with the latches (figure 4). lnsert the flexible hose in the tank entry (figure 5) and
assemble the two steel wands onto the flexible hose (figure 6). Connect the plug to the
source of electricity (figure 7), push the switch to the on position (figure 8) and start
cleaning. For the cleaning of floors or parquets, assemble the special floor brush tool
(figure 9), and for use on carpets and broadloom, assemble the carpet tool (supplied on
request) as in (figure 10). For the cleaning of hard-to-reach areas, such as the inside of
cars, etc.., you must use the crevice tool, assembled as in (figure 11) and used as in
(figure 12,13). The special dust brush for cleaning furniture, and carpets and upholstery
inside cars, and useful for the cleaning of small surfaces and angles is also included and
must be assembled as in (figure 14) and used as in (figure 15). At the end of the work
turn off the machine by pushing the switch to the off position (figure 16), disconnect the
plug from the source of electricity (figure 1) and clean the tank following the instructions
in this booklet.
TO USE AS WET VACUUM CLEANER (to vacuum liquids):
Make sure that the tank does not contain dust. Disconnect the plug from the source of
electricity (figure 17), remove the head (figure 18), remove the dust filter (figure 19).
Put the head in its original position and secure it onto the tank with the latches (figure
20), connect the plug to the source of electricity (figure 21), turn on the machine by
pushing the switch to the on position (figure 22) and start cleaning, using the special
tool (figure 23) or the squeegee tool (figure 24). At the end of the work, turn off the
machine by pushing the switch to the off position (figure 25), disconnect the plug from
the source of electricity (figure 17) and remove the liquid from the tank following the
instructions in this booklet.

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ca80Ca60Ca100

Inhaltsverzeichnis