Herunterladen Inhalt Inhalt Diese Seite drucken

Technical Data; Inserting And Removing The Battery - Bosch Active Line BDU250C Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für Active Line BDU250C:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

English – 2​

Technical data

Drive unit
Product code
Continuous rated power
Torque at drive, max.
Rated voltage
Operating temperature
Storage temperature
Protection rating
Weight, approx.
A)
Bicycle lights
B)C)
Voltage approx.
Maximum power
– Front light
– Taillight
Depends on legal regulations, not possible in all coun-
A)
try-specific models via the eBike battery
The voltage level is preset and can only be changed by
B)
the bicycle dealer.
Inserting a bulb incorrectly can cause it to blow.
Assembly

Inserting and removing the battery

For inserting and removing the eBike battery in/from the
eBike, please read and observe the battery operating in-
structions.
Checking the speed sensor (see figure A)
The speed sensor (2) and its spoke magnet (3) must be fit-
ted such that the spoke magnet moves past the speed
sensor at a distance of at least 5 mm and at most 17 mm
with each rotation of the wheel.
Note: If the distance between the speed sensor (2) and the
spoke magnet (3) is too small or too large, or if the speed
sensor (2) is not properly connected, the speedometer dis-
play will fail and the eBike drive unit will operate in emer-
gency mode.
Should this occur, loosen the screw of the spoke magnet (3)
and fasten the spoke magnet to the spoke such that it runs
past the marking on the speed sensor at the correct clear-
ance. If the speed is still not being indicated on the speedo-
meter display after doing this, please contact an authorised
bicycle dealer.
0 275 007 XD2 | (25.04.2018)
Active Line
BDU250C
BDU255C
W
250
Nm
50
V =
36
°C
-5 to +40
°C
-10 to +50
IP 54 (dust- and
splash-proof)
kg
4
When changing the bulbs, ensure that they are compat-
C)
ible with the Bosch eBike system (ask your bicycle
dealer) and are suitable for the specified voltage. Bulbs
must only be replaced with bulbs of the same voltage.
Operation
Start-up
Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged battery is inserted (see battery op-
erating instructions).
– The on-board computer is properly inserted in the holder
(see on-board computer operating instructions).
– The speed sensor is correctly connected (see "Checking
the speed sensor (see figure A)", page English – 2).
Switching the eBike system on/off
The following options are available for switching on the
eBike system:
– If the on-board computer is already switched on when you
insert it into the holder, the eBike system will be switched
on automatically.
– When the on-board computer and the eBike battery are
inserted, briefly press the On/Off button of the on-board
computer.
– With the on-board computer inserted, push the On/Off
button on the eBike battery (bicycle manufacturer-spe-
18
Performance Line
Cruise
Speed
BDU250P
BDU290P
250
63
36
-5 to +40
-5 to +40
-10 to +50
-10 to +50
IP 54 (dust- and
IP 54 (dust- and
splash-proof)
splash-proof)
4
V =
W
W
Performance
Line CX
BDU250P CX
250
250
63
75
36
36
-5 to +40
-10 to +50
IP 54 (dust- and
splash-proof)
4
4
6/12
8.4/17.4
0.6/0.6
Bosch eBike Systems

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Performance line bdu290pPerformance line bdu250pActive line bdu255cPerformance line cx bdu250p cx

Inhaltsverzeichnis