Kress 750 FDF Bedienungsanleitung Seite 8

1 Adjusting wheel
2 Swivel stop
3 Index
4 Right column guide
5 Alignment aids
6 Support shoe
7 Base plate
8 Ring switch
9 Rocker switch
10 Front edge
11 Turning knob
12 Arched handle
13 Motor housing
14 Sawdust exit nozzle
15 Sawdust catch bag
16 Suction nozzle
17 Mains cable module
18 Locking button
19 Countersink screw
20 Push plate
21 Spindle
22 Flanged nut
23 Routing tool
24 Cutting tooth
25 Nut
26 Depth adjustment stop
27 Index stop
28 Clamping flange
29 Router protection stop
Technical Specifications
Power consumption
Power output
Idling speed
Spindle thread
Max. diameter
Max. routing disk diameter
Routing disk/hub thickness
Cutting depth
Swivel range
Approx. weight
Application
The 750 FDF flat mortise router can be employed for routing
grooves in a range of materials including solid wood,
plywood, particle boards, fibreboards, plexiglass and artificial
marble with mortise type nos. 0, 10, 20, S6, H9, Simplex and
Duplex as well as for milling resin pockets in solid wood.
Safety rules and instructions which should be read
prior to operation. We strongly urge that you always
observe them for your own safety.
1. Pull mains plug prior to working on the motor. This
is especially important when changing the router or
other tools or when performing service and main-
tenance work.
2. Always clamp the workpiece securely if possible.
3. Make sure that the routing tools are sharp. Dull
tools produce poor routing results and unnecess-
arily overload the motor.
4. Make sure that the router motor is turned off when
putting the router down.
5. Always disconnect the router's power cord during
work interruptions to prevent unintentional oper-
ation!
6. Use only routing tools intended for manual tool ad-
vance.
7. The motor component of the 750 FDF mortise
router must be able to turn freely without snagging.
8. The support shoe must not be clamped in place
while the routing tool is extended.
English
750 FDF
750 W
400 W
9800 rpm
M10
22
100 mm
4/3
19 mm
0–90 degrees
3.2 kg
9. Always wear safety glasses and ear protection
while working.
10. Always install the sawdust exit pipe or the sawdust
catch connector before using the router.
11. Always guide the tool with both hands – one hand
should be placed on the arched handle, the other
on the motor housing.
12. Use the tool only for the kinds of work described in
the user manual.
13. The two turning knobs (11) of the swivel stop must
be tightened securely during router operation.
14. Outside power sockets must be protected with re-
sidual-current-operated circuit-breakers (r.c.c.b.).
15. Do not drill holes into the housing to label the ma-
chine. The protective insulation will be bridged.
Please use self-adhesive labels.
16. Always lead cables away towards the back of the
machine.
Safety instructions and prevention of accidents
Before operating the machine, please read through the
operating instructions completely, follow the Safety In-
structions in this manual as well as the general Safety In-
structions for Power Tools in the accompanying booklet.
Double insulation
Our equipment is designed in accordance with European
regulations (EN standards) for the utmost safety of the
user. Machines with double insulation always carry the in-
ternational symbol. The machines do not require earth-
ing. A two-core cable is sufficient.
The machines are interference-suppressed in accordance
with EN 55014.
Initial operation
Before the first operation check that the mains voltage cor-
responds to that given on the machine nameplate.
Connection types
The 750 FDF mortise router can be used for the following
types of joints in solid wood, plywood, particle board, fibre
board, plexiglass und and artificial marble.
Corner joint
Miter joint Centre wall joint
Selection of mortise sizes
Workpiece thickness Mortise size
8-12 0
12-15 10
>15 20
Always use the largest possible mortise size for an optimal
joint. For workpiece thicknesses above 25 mm, 2 mortises
may be used.
Lengthwise
or cross joint
Frame joint
Dimensions
47 x 15 x 4 mm
53 x 19 x 4 mm
56 x 23 x 4 mm