Audio Settings - Kenwood KDC-U31R Bedienungsanleitung

AUDIO SETTINGS

While listening to any source...
1
Press AUDIO to select [AUD CTRL].
2
Turn the volume knob to make a selection (see the table below), then press
the knob.
2
Repeat step until the desired item is selected or activated.
3
Press and hold to exit.
• To return to the previous hierarchy, press
SW LEVEL –15 to +15 (0): Adjusts the subwoofer output level.
BASS LVL –8 to +8 (0):
Adjusts the level to memorize for each source. (Before making
MID LVL –8 to +8 (0):
an adjustment, select the source you want to adjust.)
TRE LVL –8 to +8 (0):
EQ PRO
BASS ADJ BASS FRQ 60/ 80/ 100/ 200: Selects the center frequency.
BASS LVL –8 to +8 (0): Adjusts the level.
BASS Q 1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXT B-EX ON: Turns on the extended bass. ; B-EX OFF: Cancels.
MID ADJ MID FRQ 0.5K/ 1.0K/ 1.5K/ 2.5K: Selects the center frequency.
MID LVL –8 to +8 (0): Adjusts the level.
MID Q 0.75/ 1.00/ 1.25: Adjusts the quality factor.
TRE ADJ TRE FRQ 10.0K/ 12.5K/ 15.0K/ 17.5K: Selects the center frequency.
TRE LVL –8 to +8 (0): Adjusts the level.
EQ NATURAL/ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL: Selects
a preset equalizer suitable to the music genre. (Select [USER] to use the
customized bass, middle, and treble settings.)
B. BOOST BB-L LV1/ BB-L LV2/ BB-L LV3: Selects your preferred bass boost level. ;
BB-L OFF: Cancels.
8
.
Default: XX
LOUDNESS LOUD LV1/ LOUD LV2: Selects your preferred low and high frequencies boost
to produce a well-balanced sound at a low volume level. ; OFF: Cancels.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.
FADER R15 to F15 (0): Adjusts the rear and front speaker output balance.
SW SET SW ON: Turns on the subwoofer output. ; SW OFF: Cancels.
DTIL SET
LPF SW LPF THRU: All signals are sent to the subwoofer. ; LPF 85HZ/ LPF 120HZ/
LPF 160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/ 160 Hz
are sent to the subwoofer.
SW PHASE PHAS REV (180°)/ PHAS NML (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [LPF THRU] is selected for [LPF SW].)
SPRM SET SPRM ON: Creates realistic sound by interpolating the high-frequency
components that are lost in AAC/MP3/WMA audio compression. ;
SPRM OFF: Cancels. (Selectable only when playing back an AAC/MP3/WMA
disc or a USB device, except iPhone/iPod.)
V-OFFSET –8 to +8 (for AUX) ; –8 to 0 (for other sources): Presets the volume
(Default: 0) adjustment level of each source. (Before adjustment, select the source you
want to adjust.)
• [SW LEVEL]/ [SW SET]/ [LPF SW]/ [SW PHASE] is selectable only if [SWPRE] is set to
[SWPRE SW]. (➜ 4)
• [SW LEVEL]/ [LPF SW]/ [SW PHASE] is selectable only if [SW SET] is set to [SW ON].