Installation - Sygonix 1397543 Bedienungsanleitung

• To prevent risks, damaged power cables may only be replaced
by the manufacturer, a professional workshop appointed by the
manufacturer, or a similarly qualified person.
• Never plug in or unplug the mains plug when your hands are wet.
• Uncoil the power cable fully. Failure to do so may result in
overheating. T his poses a fire hazard!
• Make sure that the mains cable is not squeezed, bent, damaged
by sharp edges or put under mechanical stress. Avoid excessive
thermal stress on the mains cable from extreme heat or cold. Do
not modify the mains cable. Otherwise the mains cable may be
damaged. A damaged mains cable can cause a deadly electric
shock.
• Do not touch the mains cable if it is damaged. First, power down
the respective mains socket (e.g. via the respective circuit breaker)
and then carefully pull the mains plug from the mains socket.
Never use the product if the mains cable is damaged.
• Do not use an extension cord, power strip or any other electronic
ballast devices. Connect the power plug to a wall power outlet
only.
• There must be at least 100 cm between the device and flammable
materials and objects (i.e. curtains, doors, furniture, etc.). Failure
to heed this minimum safety clearance poses a fire hazard!
• Use in spaces with a great amount of dust, with flammable gases,
vapors or solvents is not permitted. There is a danger of fire and
explosion!
• Never leave the product unattended during use.
• The protective grille becomes hot very fast. Risk of burning! Use
appropriate caution when handling the product. Never touch it
with your bare hands.
• Unpleasant odors may occur for some time during first use. Make
sure the room where the product is set up is sufficiently ventilated.
• Move, transport and store the product only when it is fully cooled
off.
• Use the product in temperature climates only, do not use in the
tropics.
• Do not use the product just after moving it from a cold to a warm
space. This may cause condensation, which can destroy the
device or lead to electric shock. Allow the device to reach room
temperature first. Wait until the condensation has evaporated. T his
can take a few hours. Only after that you may connect the product
to the power supply and use it.
• Shield the product from extreme temperatures, direct sunlight,
strong blows, combustible gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out
of operation and protect it from any accidental use. Safe operation
can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Caution, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• Correct polarity must
(rechargeable) batteries.
• (Rechargeable) batteries should be removed from the device if it
is not used for a long period of time to avoid damage through
leaking. Leaking or damaged (rechargeable) batteries might
cause acid burns when in contact with skin, therefore use suitable
protective gloves to handle corrupted (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of children. Do
not leave (rechargeable) batteries lying around, as there is risk,
that children or pets swallow them.
• All (rechargeable) batteries should be replaced at the same time.
Mixing old and new (rechargeable) batteries in the device can lead
to (rechargeable) battery leakage and device damage.
• (Rechargeable) batteries must not be dismantled, short-circuited
or thrown into fire. Never recharge non-rechargeable batteries.
There is a risk of explosion!
• Consult a professional if you require assistance with product
operation, safety or connection.
• Maintenance work, adjustments and repairs may be carried out
only by a professional or at a specialist workshop.
• If you have questions which remain unanswered by these
operating instructions, contact our technical support service or
other technical personnel.
Inserting/replacing batteries (remote control)
1. Remove the battery compartment lid.
2. Insert two AAA batteries with the correct polarity. Observe the
polarity markings inside the compartment.
3. Close the battery compartment.
Replace the batteries, once the brightness of the flashlight reduces
significantly.

Installation

a) Mounting accessories
1
4 5
No. Description
1 Foot
2 Foot screw
3 Bottom wall mount
4 Top wall mount
5 Dowel for wall mount
6 Screw for bottom wall mount
7 Screw for top wall mount
be observed while inserting
2
3
6 7
the
Number
1
2
1
2
3
1
2