Delivery Content; Safety Instructions - Renkforce 1369246 Bedienungsanleitung

Operating instructions
Camera dummy with solar and LED lights
Item no. 1369246
Intended use
This product is a dummy that resembles a functional surveillance camera and is
intended for use as deterrent in secluded and critical areas (e.g. driveways, entrance
areas, etc.). The product is suitable for outdoor installation. The power supply requires
3 rechargeable batteries (not included) that will be charged via built-in solar module.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.

Delivery content

• Camera dummy
• 3x screws
• 3x dowels
• Warning sticker
• Operating instructions

Safety instructions

Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, strong jolts, flammable
gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Never point a garden hose at the product.
• The product may not be mounted in or under water.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• For installations in industrial facilities, follow the accident prevention
regulations for electrical systems and equipment of the government
safety organization or the corresponding authority for your country.
• Correct polarity must be observed while inserting the rechargeable
batteries.
• Rechargeable batteries should be removed from the device if it is not
used for a long period of time to avoid damage through leaking. Leaking or
damaged rechargeable batteries might cause acid burns when in contact
with skin, therefore use suitable protective gloves to handle corrupted
rechargeable batteries.
• Rechargeable batteries must be kept out of reach of children. Do not leave
rechargeable batteries lying around, as there is risk, that children or pets
swallow them.
• All rechargeable batteries should be replaced at the same time. Mixing old
and new rechargeable batteries in the device can lead to rechargeable
battery leakage and device damage.
• Rechargeable batteries must not be dismantled, short-circuited or thrown
into fire. Never recharge non-rechargeable batteries. There is a risk of
explosion!
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Function of the motion detector
• The PIR sensor integrated in the product responds to temperature changes within
the detection range. Such is the case when humans or animals, whose temperatures
differ from the ambient temperature, enter the detection range.
• In order to allow for maximum detection, the product should be positioned in such
a way that the object to be detected does not walk towards the motion detector but
crosses the detection range from left to right or vice versa. Keep that in mind when
installing the product.
• The range of detecting temperature changes depends on a variety of factors:
- Installation height
- Ambient temperature
- Temperature difference between the moving object and the environment
- Size of the object
- Distance between object and product
- Direction and speed of motion
Detecting temperature changes through glass is basically not possible. Do
not install the product behind a pane of glass.
Preparing installation
• Select a stable, vertical surface (e.g. the wall of buildings or garages).
• The product is suitable for use in unprotected outdoor areas. It must however not
be used in or under water.
• Consider the position of the solar module when selecting the installation location.
• Install the solar module at a location with good light conditions and facing the south,
in order for the solar module to charge the batteries during daytime. Make sure that
the solar module is not covered or shaded, i.e. by trees or buildings.
• Make sure that the solar module is free of snow or anything else which might block
it.
• Do not install the solar module near other light sources that simulate daylight (e.g.
street lights), in order to prevent the product from switching on.