Operation; Technical Data; Cleaning And Care - VOLTCRAFT CPUC-1000 Bedienungsanleitung

OPERATION

Always turn off the device to be connected before plugging it into the USB
socket (1). Make sure the connection is correct. If plugged in incorrectly, the
product may overheat and cause an electric shock, start a fire or otherwise
lead to damages to persons or property.
Make sure that the connected device's current consumption does not
exceed the product's output current. Observe the information in the chapter

"Technical data".

Unplug the product for extended periods of disuse.
a) Inserting/exchanging adaptors
1. Select one of the five included adaptors (4, 5, 6, 7, 8) and insert it correctly into the adaptor
plug-in position (2) on the bottom of the USB power adaptor. It is only possible to connect
in one way.
2. Push the adaptor toward the locking lever (3) until the adaptor clicks into place.
3. To remove the adaptor, push down the locking lever with a tool (i.e. screwdriver or a pen
tip). Then push the adaptor away from the locking lever and remove it.
4. Follow the same steps to insert another adaptor.
b) Operation with power plug adaptor
1. Connect your USB device (make sure it is off) to the USB socket (1).
2. Connect the USB power adaptor plug (4, 5, 6, 7) to a common household power outlet.
The white LED ring on the USB plug lights up to signalize that the USB power adaptor is
operational.
3. The connected USB device is now charging. Should you wish to operate the USB device,
you may turn it on now.
4. Turn off your USB device before unplugging it from the USB power adaptor.
c) Operation with car adaptor
1. Connect your USB device (make sure it is off) to the USB socket (1).
2. Connect the USB power adaptor car adaptor (8) to your car's cigarette lighter socket.
The white LED ring on the USB plug lights up to signalize that the USB power adaptor is
operational.
3. The connected USB device is now charging. Should you wish to operate the USB device,
you may turn it on now.
4. Turn off your USB device before unplugging it from the USB power adaptor.
You can operate the USB power adaptor if your engine is on or off. However, do not
start your engine as long as the USB power adaptor is connected. The power to the
cigarette lighter is cut briefly when the engine starts (this does not need to apply to all
car models). If the engine is switched off, drawing current over a longer period of time
will discharge the vehicle battery.
CHANGING THE FUSE (CAR ADAPTOR)
1. Turn the cap on the tip of the car adaptor (8) counter clockwise.
2. Remove the defective fuse and replace it with a fuse of the same type.
3. Replace the cap and tighten it by turning clockwise.
4. Check to see whether the car adaptor is functioning properly.

CLEANING AND CARE

Do not use any aggressive cleaning agents, rubbing alcohol or other chemical
solutions as they can cause damage to the housing and malfunctioning.
• Before cleaning, unplug the product and all devices from the power supply.
• Never submerge the product in water.
• There are no components located inside the product you need to maintain. Never open/
dismantle the product.
• To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much
pressure to the housing to prevent scratching.
• Use a longhaired, soft and clean brush and a vacuum cleaner to easily remove dust.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TECHNICAL DATA
Input voltage ................................. 100 – 240 V/AC, 50/60 Hz (operation with power plug)
................................................. 12 – 13.8 V/DC (operation with car adaptor)
Output voltage / current ................ 5 V/DC, 1000 mA
Fuse (car adaptor) ........................ 1 A, 250 V
Operating conditions ..................... 0 to +35 ºC, 20 – 90 % RH (non-condensing)
Storage conditions ........................ -20 to +60 ºC, 10 – 90 % RH (non-condensing)
Dimensions (Ø x H) ...................... 56 x 32 mm
Weight .......................................... 138 g
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 96 04 / 40 87 80
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2013 by Voltcraft®