Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DL-LED102 LED Effect Beamer
Item no. 59 14 86
1.
Intended use
This product is used to generate lighting effects on dance floors, in party rooms etc. It is approved only for
connection to a standard wall socket. Do not use other power supplies. It must only be used in enclosed spaces
and therefore not outside. Contact with moisture must be avoided at all times.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2.
Delivery content
•
LED effect beamer
•
Suspension bracket
•
2 x screws
•
Operating instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety information. If
you do not follow the safety instructions and information on proper handling in this manual,
we assume no liability for any resulting personal injury or damage to property. Such cases
will invalidate the warranty/guarantee.
Persons / Product
•
Point the light beam in such a way that it is directed below eye level.
•
Never look directly or with optical instruments into the light beam.
•
Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of
injury.
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
product.
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
•
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4.
Positioning / Mounting
Positioning
Place the effect beamer onto an even, clean surface. Ensure the device is placed on a stable surface so that
it cannot fall down.
Mounting
Only tighten the screws by hand! Do not use any tools to tighten the screws.
•
Fasten the mounting bracket at the screw openings located on the outer sides of the effect beamer. Insert
one washer each between mounting bracket and effect beamer and then attach the mounting bracket using
the two screws.
•
Install the effect beamer using a mounting bracket on the ceiling, the wall or on a suitable crossbeam. When
installing it, make sure that the device cannot swing freely.
•
Secure the device with fastenings that are compatible with the fastening surface and suitable for carrying
the weight of the light effect device.
•
Secure the installation with an additional suitable safety restraint cable or net. The safety restraint cable or
net must be able of supporting the light effect device in the event of a fault in the main support system.
•
Set the required tilt angle by slightly loosening the screws and tilting the effect beamer. Tighten the screws
again after the adjustment.
5.
Operation
1.
To use the effect beamer, connect the mains plug to a standard wall socket.
2.
Turn the "Sound Sensitivity" control dial and the "Speed" control dial counterclockwise as far as they will
go.
3.
Turn the effect beamer on using the on / off switch.
4.
To have the effect beamer flash constantly, turn the "Speed" control dial clockwise until the required speed
is set.
5.
To use the effect beamer with music synchronisation, deactivate the "Speed" function by turning the "Speed"
Version 11/11
control dial counterclockwise as far as it will go. Then, set the required microphone sensitivity by turning
the "Sound Sensitivity" control dial clockwise. The effect beamer creates a rotating lighting effect to the
beat of the music.
6.
To create a flashing and rotating lighting effect, turn both control dials clockwise until the required intensity
level has been reached.
7.
After use, turn the effect beamer off using the on / off switch.
8.
If you will not use the product for a longer period of time, unplug the mains plug from the wall socket.
6.
Replacing the fuse
1.
Disconnect the mains plug from the wall socket.
2.
Remove the fuse from the top right rear side of the effect beamer using a Phillips screwdriver.
3.
Replace the fuse with a new one of the same type and screw it in tightly.
7.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
8.
Technical data
Operating voltage:
Power consumption:
Cable length:
Fuse:
Number of LEDs:
Operating temperature :
Operating humidity:
Storage temperature:
Storage humidity:
Dimensions (W x H x D):
Weight:
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2011 by Conrad Electronic SE.
220 – 240 V/AC, 50 Hz
6.4 W
110 cm
1 A, 250 V
18 (6 x red, 6 x green, 6 x blue)
-10 to +45 °C
20 – 95 %
-20 to +55 °C
10 – 95 %
154 x 100 x 225 mm (excl. bracket) / 205 x 100 x 225 mm (incl. bracket)
1.46 kg
V1_1111_02-JU
Werbung
