Tips For Operation; Replacing The Rotor Blades - REVELL BIG ONE PRO Bedienungsanleitung

• Make sure to return the thrust controller on the remote control to the lowest position after an "emergency landing" in order to prevent damages to the electronics and rotor blades.
• Always completely switch off the flying machine and remote control after use and unplug the plug on the cable for the flight operation on the helicopter. Otherwise a start command
could follow accidentally.
If the rotor blades on the helicopter become damaged and have to be replaced, switch the remote control to "OFF" and disconnect the plug from the helicopter battery. Then proceed as follows:
Ensure before installation
that you have not mixed
up the rotor blades. The rotor
blades are marked
"A" and"B" (see Fig.)
Type "A" rotor blades are
installed on the top and type
"B" rotor blades are installed
below.
1. Remove the casing from the helicopter as shown (fig. 1 a/b)
2. Open the retainer braces with a Philips screwdriver and
remove the battery (fig. 2)
3. When inserting a new Li-Po battery, pay attention to the
same position so that the distribution of weight and the flight
performance of your helicopter remains the same (fig. 3).
By the way: suitable Li-Po batteries can be found at
www.revell-control.de/Ersatzteile!
4. Ensure the secure hold of the battery by using double-sided
sticky tape if necessary, and by tightening the retainer braces.
Place the casing back on the fuselage (fig. 4).
5. Pay attention to the disposal information for the battery on
page 1.
Problem:
the rotor blades do not move.
Problem:
The radio control does not work.
Problem:
the helicopter cannot be operated
with the radio remote control.
Problem:
The helicopter does not ascend
Problem:
The helicopter loses thrust during
the flight without any apparent
reason and descends.
Problem:
the helicopter lands too quickly.
At www.revell-control.de, you can find our possibilities to order,
replacement tips for spare parts, and further useful information
10

Tips for operation

Replacing the rotor blades

changing the Li-Po battery
fig. 1a
Safety tips
Resolution of errors
Cause:
• The ON/OFF switch is set to "OFF".
• The battery is too low or empty.
Cause:
• The ON/OFF switch is set to "OFF".
• The batteries were not inserted correctly.
• The batteries are too weak.
Cause:
• The switch on the radio control is set to "OFF".
• The helicopter switch is turned to "OFF"
• The antenna on the radio control is not inserted
corrected and/or not fully extended.
Cause:
• The rotor blades rotate too slowly.
• There is not enough battery power.
Cause:
• The battery is too weak.
Cause:
• Loss of throttle control.
• The thrust controller is pulled down
too quickly.
Service guidelines
on all Revell control models.
1. Take a Phillips screwdriver and carefully unscrew the screws
on the rotor blade.
2. Now carefully pull the rotor blade off the holder.
3. Insert the new rotor blade carefully into the holder and
tighten the screw. Caution: Do not screw in the screw too
tightly. The rotor blade must have some play.
fig. 2
fig. 1b
Remedy:
• Set the ON/OFF switch to "ON".
• Recharge the battery (see "Charging the aircraft
battery" section).
Remedy:
• Set the ON/OFF switch to "ON".
• Check that the batteries are correctly inserted.
• Insert new batteries.
Remedy:
• Switch the switch on the radio remote control to "ON".
• The helicopter switch is turned to "ON"
• Check antenna and extend to full height.
• Repeat the take-off procedure and/or replace the
batteries and/or recharge
Remedy:
• Push the throttle stick up.
• Recharge the battery (see "Charging the
aircraft battery" section).
Remedy:
• Recharge the battery (see "Charging the
aircraft battery" section).
Remedy:
• Slowly move the throttle stick to the down position.
fig. 3
fig. 4
www.revell-control.de