Recording; Menu Structure - Tascam DR-22WL Bedienungsanleitung

Level meter
6
The level of input sound is shown.
When the auto-recording function is on, the level at
which auto-recording starts is shown as a frame.
7 Pre-recording setting status
Blank: Pre-recording off
: Pre-recording on
Recorder operation status
8
Auto-recording setting status
9
Blank: Auto-recording off
: Auto-recording on
File name
0
The file name that will automatically be given to the
recorded file is shown.
Function button information
q
These icons show the recorder operation status.
Indicator Meaning
Recording in standby or recording paused
09
Recording in progress
0
Peak value in decibels (dB)
w
The peak recording level value is shown digitally.
is shown when recording over the maximum input
level (−2 dB or more).
Elapsed recording time
e
The elapsed recording time of a recorded file is shown as
hours : minutes : seconds.
Remaining recording time
r
The remaining recording time for the microSD card is
shown as hours : minutes : seconds.
10
TASCAM DR-22WL

Recording

By selecting with the scene dial, you can record easily with an
optimized setting for the scene you want to record.
Purpose Mark Name
Record easily right away
Record loud sounds
Record a concert or chorus
Record an instrument such as a guitar
Record an interview
8 Recording easily right away
Set the scene dial to .
1.
Press the RECORD button to start recording immediately.
2.
NOTE
The input level is adjusted automatically (you cannot
change manually).
/MENU/8 button to finish recording.
Press the
3.
8 Recording using selected scene settings
Set the scene dial to the scene ( / / / ) you want to
1.
record.
Press the RECORD button to enter recording standby.
2.
Use the INPUT LEVEL volume control to adjust the input
3.
level.
To obtain higher quality, it is recommended that you
record as loud a sound as possible. Raise the input level
so that the −12 dB indicator lights green in order to
optimize the recording level. If the input level is set too
high, the sound may be distorted. To avoid this, lower the
input level when the PEAK indicator lights red.
Press the RECORD button again to start recording.
4.
Press the /MENU/8 button to finish recording.
5.
8 Recording using the manual mode
Set the scene dial to .
1.
Press the RECORD button to enter recording standby.
2.
Use the INPUT LEVEL volume control to adjust the input
3.
level.
To obtain higher quality, it is recommended that you
record as loud a sound possible. Raise the input level
so that the −12 dB indicator lights green in order to
optimize the recording level. If the input level is set too
high, the sound may be distorted. To avoid this, lower the
input level when the PEAK indicator lights red.
Press the RECORD button again to start recording.
4.
When recording starts, the REC indicator lights continu-
EASY
ously and the display shows the elapsed recording time
LOUD
and the remaining recording time.
MUSIC
Press the
5.
INSTRUMENT
8 Pausing recording
INTERVIEW
You can pause recording and then continue recording in the
same file.
While recording, press the RECORD button to pause.
1.
Press the RECORD button again to resume recording.
2.

Menu structure

REC
FORMAT
SAMPLE
TYPE
PRE REC
AUTO FUNC
DUAL FORMAT
COUNT INIT
PEAK HOLD
/MENU/8 button to finish recording.
Set the file format
WAV: 16/24 bit,
MP3: 32 k–320 kbps
Set the sampling frequency
44.1/48/96 kHz (96 kHz for WAV only)
Set to mono or stereo
MONO, STEREO
Set the pre-recording function
ON, OFF
Set the track incrementation, auto-recording,
and mark function
TRACK INCREMENT, AUTO REC, PEAK
MARK, AUTO MARK
Set dual format recording
OFF,
MP3: 32 k–320 kbps
Reset the number used as the file name
Set the peak hold function
OFF, ON