Before Starting The Equipment; Assembling The Components - EINHELL GE-PM 48 S HW-E Li Originalbetriebsanleitung

Vibration emission value a
K uncertainty = 1.5 m/s
GE-PM 53 S HW-E Li
Engine type ........One-cylinder four-stroke engine,
...................................................................173 cc
Power input: .............................................. 2.8 kw
Working speed n : ...................... 2850 ± 100 min
0
Fuel: ............................................................ Petrol
Tank capacity: .................................. approx. 1.6 l
Engine oil: ........................... approx. 0.6 l / 10W30
Spark plug: ................................................ F7RTC
Electrode gap (spark plug): ............. 0.7 ± 0,1 mm
Cutting height adjustment: ... Central, (25-70 mm)
Cutting width: .......................................... 530 mm
Weight: ......................................................44,1 kg
Danger!
Sound and vibration
L sound pressure level ..................... 83.8 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 96.5 dB(A)
WA
K uncertainty ........................................ 1.93 dB
WA
Guaranteed sound power level ............ 98 dB(A)
Vibration emission value a
K uncertainty = 1.5 m/s
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Long work periods should be avoided due to the
development of high noise and vibration levels.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Anl_GE-PM_53_48_S_HW-E_Li_SPK9.indb 29 Anl_GE-PM_53_48_S_HW-E_Li_SPK9.indb 29
= 5.66 m/s
2
h
2
-1
= 7.12 m/s
2
h
2
- 29 -
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Damage to hearing if no suitable ear protec-
tion is used.
2. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

5.1 Assembling the components

Some parts of the equipment come disassem-
bled. For quick and easy assembly, read and
follow the instructions below.
Note! You will need the following additional tools
(not supplied) for assembly, and also for mainte-
nance work:
•
One flat oil drip tray (for changing the oil)
•
One 1 liter measuring jug (oil/petrol resistant)
•
One petrol can
•
One funnel (suitable for the tank's petrol filler
neck)
•
Household wipes (to wipe up oil/petrol resi-
due; dispose of these at a filling station)
•
One petrol suction pump (plastic, available
from DIY stores)
•
One oil can with hand pump (available from
DIY stores)
•
Engine oil
Assembly
1. Fit the push bar (Item 3) as shown in Fig.
3a-3b. For fastening choose one of the holes
(Fig. 3a/Item A) to suit the required height of
the handle.
Important! The identical height must be set
on both sides.
2. Fit the Power-X combi-panel (Item 15) with
the supplied screws as shown in Fig. (3c and
3d).
3. Insert the grip of the starter cable (Item 9) into
the hook provided for that purpose as shown
in Fig. 1.
4. Fasten the actuator cables to the push bar
with the supplied cable clips (Items 10a and
10b) as shown in Fig. 3e.
5. Lift the ejector fl ap (Item 5a) with one hand
12.10.2017 12:53:30 12.10.2017 12:53:30