Hettich BLUE MAX miniTyp 2/6 Betriebsanleitung Seite 17

ATTENTION!
Never enter the protection zone and instruct a second person to
switch the machine on from outside.
2. While work is in progress on the machine, no other persons must
be present in the safety zone and working area in front of and
behind the machine.
3. Do not reach into the drill unit operating area while production
is in progress. Suitable aids must be used to push small parts
against stops. Risk of getting crushed!
J) Safety devices
Pay attention to safety devices.
1. Do not remove the factory-fitted safety devices, protective hoods
and switches. All safety and hazard warnings on the machine
must be completely legible at all times.
2. Safety devices must not be rendered inoperative.
3. If safety covers need to be dismantled for tool changes or
cleaning and maintenance, always make sure that they are
refitted before returning the machine to operation. Check that
they are in proper working order.
4. Operating the machine without these covers gives rise to hazards
from flying shavings and enables persons to reach inadvertently
into moving tools or parts of the machine that pose a threat of
getting crushed.
K) Repair and maintenance
Always switch machine off before attempting repair or
maintenance work.
1. Operating personnel must be informed before conducting
maintenance or repair work.
2. Always disconnect the plug when working in the machine or on
the electrical system!
3. In cases where lifting gear is used for dismantling or installing
assemblies, ensure that the lifting gear is safe and pay attention
to careful and proper attachment.
4. Repair and maintenance work, in particular on electrical
equipment, must be performed by qualified personnel only.
5. When working on the electrical system, follow the pertinent
guidelines. Verify safe isolation from the power supply, properly
earthing or shorting where necessary.
6. Only use safety fuses with the prescribed ratings; too high a fuse
rating will irreparably damage the system. If fuses trip frequently,
instruct a qualified electrician to locate and remedy the fault
before switching the machine back on again.
7. Only use lubricants prescribed by the manufacturer.
When handling oils and greases, observe the safety regulations
applicable to the product in question.
8. Use only OEM spare parts or, in the case of standard parts, parts
of at least the same quality.
9. Remove dust and any shavings from the machine by suction.
10. When carrying out repair work on the units, do not transpose
switch plugs. This may result in malfunctions and hazards from
extended tools. Adhere to factory wiring.
L) Noise! Wear ear protection devices.
1. Wear ear protection devices during noisy work processes.
M) Dust
Dangers to health from wood dust.
1. Equipped with the suction devices designated, the machine
conforms to dust protection regulations.
2. Some work processes and specific workpieces (e.g. framed doors,
fascias strips or special profiles) may nor permit full encapsula-
tion and suction extraction. Wear dust protection masks!
N) Leftover pieces
Design workpieces in such a way as to avoid leftover pieces
flying out of the machine with great force.
O) Processing forces
Adapt material feed and cutting volume to the retention
force for the material concerned.
1. If retention problems are encountered, use additional stops,
templates or power-operated clamping devices.
P) Fire hazard
Only perform grinding and welding work when the machine is
clean; fire hazard!
1. Observe welding regulations and accident prevention regulations.
Q) Explosion protection
The machine is not explosion protected. Do not set it up in
the vicinity of painting shops.
R) Faulty operation
The machine operator must inspect the machine daily for
externally visible defects.
1. Defects must be rectified immediately; if other personnel are
responsible for rectifying defects, they must be reported to such
personnel with the request that they be repaired.
2. The machine must only be operated if it is in perfect working
order.
3. The area around the machine must be kept clean and must not
contain any obstacles over which persons may stumble.
Extraction hoses must be routed in such a way that they do not
restrict the movement of the machine operator.
4. Planned maintenance work must be carried out at the intervals
specified. If necessary, the owner must prescribe other suitable
intervals or specify additional work.
17
GB GB