Bosch Uneo Originalbetriebsanleitung Seite 11

OBJ_BUCH-1695-004.book Page 11 Friday, September 2, 2016 3:45 PM
 The maximum torque is reached only in the screwdriving
operating mode (1. gear). The maximum no-load speed is
reached only in the operating modes drilling and hammer
drilling.
 Replace a damaged dust protection cap immediately.
The dust protection cap largely prevents the penetration of
drilling dust into the tool holder during operation. When in-
serting the tool, pay attention that the dust protection cap
is not damaged.
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
 If the application tool should become blocked, switch
the machine off. Loosen the application tool.
 When switching on with a blocked drilling tool, high
torque reaction can occur.
 Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 To save energy, only switch the power tool on when using
it.
 Avoid unintentional switching on. Ensure the On/Off
switch is in the off position before inserting battery
pack. Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power
tools that have the switch on invites accidents.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
 In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
 Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
 The battery can be damaged by pointed objects such as
nails or screwdrivers or by force applied externally. An
internal short circuit can occur and the battery can burn,
smoke, explode or overheat.
Bosch Power Tools
 The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery
in the battery charger before using your power tool for
the first time.
 Read the operating instructions of the battery charger.
 Check the tight seating of the battery. Two locking lev-
els are possible.
The battery charge-control indicator indicates the charge
condition of the battery for a few seconds when the On/Off
switch is pressed half or fully through. It consists of a three-
colour illuminating LED.
LED
Continuous lighting, green
Continuous lighting, orange
Continuous lighting, red
Flashing light, red
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the machine in a better and safer
manner.
Symbol Meaning
Uneo: Cordless Rotary Hammer
Grey-marked area: Handle
(insulated gripping surface)
Article number
Read all safety warnings and all instruc-
tions
Before any work on the machine itself,
remove the battery from the power
tool.
Wear protective gloves
Always wear ear protection.
Wear safety glasses/goggles
Keyless drill chuck
English | 11
Capacity
≥ 66 %
> 33 % —66 %
> 11 % —33 %
≤ 11 %
1 609 92A 351 | (2.9.16)