Herunterladen Inhalt Inhalt Diese Seite drucken

Codierung Des Statusbytes Beim Pa-Ausgangswert - VEGA VEGABAR 53 Betriebsanleitung

Vorschau ausblenden Andere Handbücher für VEGABAR 53:
Inhaltsverzeichnis

Werbung

Der Status "Messwert OK" ist als 80 (hex) codiert (Bit7 = 1, Bit6 ... 0 = 0).
Der Messwert wird als 32 Bit Gleitpunktzahl im IEEE-754-Format übertragen.
Byte n
Bit
Bit
Bit
Bit
Bit
Bit
Bit
7
6
4
3
5
2
VZ
2
7
2
2
2
4
2
6
5
3
Sign
Exponent
Bit
VZ
(Exponent - 127)
Value = (-1)
2
Abb. 34: Datenformat des Messwerts

Codierung des Statusbytes beim PA-Ausgangswert

Status-
Beschreibung lt. Profibus-
code
norm
0 x 00
bad - non-specific
0 x 04
bad - configuration error
0 x 0C
bad - sensor failure
0 x 10
bad - sensor failure
0 x 1f
bad - out of service constant
0 x 44
uncertain - last unstable value
0 x 48
uncertain substitute set
0 x 4c
uncertain - initial value
0 x 51
uncertain - sensor; conversion
not accurate - low limited
0 x 52
uncertain - sensor; conversion
not accurate - high limited
0 x 80
good (non-cascade) - OK
0 x 84
good (non-cascade) - active
block alarm
0 x 89
good (non-cascade) - active ad-
visory alarm - low limited
0 x 8a
good (non-cascade) - active ad-
visory alarm - high limited
0 x 8d
good (non-cascade) - active cri-
tical alarm - low limited
VEGABAR 53 • Profibus PA
Byte n+1
Bit
Bit
Bit
Bit
Bit
Bit
0
4
1
7
6
5
3
2
2
2
-3
2
1
2
0
2
-1
2
-2
2
-4
Significant
(1 + Significant)
Mögliche Ursache
Flash-Update aktiv
– Abgleichfehler
– Konfigurationsfehler bei PV-Scale (PV-Span too small)
– Maßeinheit-Unstimmigkeit
– Fehler in der Linearisierungstabelle
– Hardwarefehler
– Wandlerfehler
– Leckpulsfehler
– Triggerfehler
– Messwertgewinnungsfehler
– Temperaturmessungsfehler
"Out of Service"-Mode eingeschaltet
Failsafe-Ersatzwert (Failsafe-Mode = "Last value" und bereits gülti-
ger Messwert seit Einschalten)
– Simulation einschalten
– Failsafe-Ersatzwert (Failsafe-Mode = "Fsafe value")
Failsafe-Ersatzwert (Failsafe-Mode = "Last valid value" und noch
kein gültiger Messwert seit Einschalten)
Sensorwert < untere Grenze
Sensorwert > obere Grenze
OK
Static revision (FB, TB) changed (10 sek. lang aktiv, nachdem Pa-
rameter der Static-Kategorie geschrieben wurde)
Lo-Alarm
Hi-Alarm
Lo-Lo-Alarm
Byte n+2
Bit
Bit
Bit
Bit
Bit
Bit
Bit
4
7
6
5
0
2
1
2
-10 -11 -12 -13 -14 -15 -16 -17
2
2
-9
2
2
-8
2
-5
2
-6
-7
Significant
Bit
Bit
Bit
Bit
Bit
Bit
Bit
0
3
2
1
7
6
5
2
-18 -19 -20 -21 -22 -23
2
2
2
2
2
2
10 Anhang
Byte n+3
Bit
Bit
Bit
Bit
Bit
4
3
2
1
0
2
2
2
2
2
Significant
59

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis