Maintenance And Service - Bosch GKS Professional 85 Originalbetriebsanleitung

Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 3 and keep
it pressed.
To switch off the machine, release the On/Off switch 3.
Note: For safety reasons, the On/Off switch 3 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
Reduced starting current
The electronic reduced starting current limits the power con-
sumption when switching the tool on and enables operation
from a 13 ampere fuse.
Working Advice
Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting di-
rection. Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade. There-
fore, use only sharp saw blades that are suited for the material
to be worked.
 Before any work on the machine itself, pull the mains
plug.
Sawing Wood
The correct selection of the saw blade depends on the type
and quality of the wood and whether lengthway or crossway
cuts are required.
When cutting spruce lengthways, long spiral chips are
formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing Non-ferrous Metals
Note: Use only a sharp saw blade that is suitable for non-fer-
rous metals. This ensures a clean cut and prevents blade bind-
ing.
Guide the switched on power tool against the workpiece and
carefully start the cut. Continue the cut with low feed and
without interruption.
When sawing profiles, always begin the cut from the narrow
side; when sawing U-profiles, never start the cut from the
open side. Support long profiles in order to avoid blade bind-
ing and kickback of the power tool.
Sawing with Parallel Guide (see figure E)
The parallel guide 11 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Loosen wing bolt 7 and slide the scale of the parallel guide 11
through the guide in the base plate 14. Adjust the desired cut-
ting width as the scale setting at the respective cutting mark 9
or 10; see Section "Cutting Marks". Tighten wing bolt 7 again.
Bosch Power Tools
Sawing with Auxiliary Guide (see figure F)
For sawing large workpieces or straight edges, a board or
strip can be clamped to the workpiece as an auxiliary guide;
the base plate of the circular saw can be guided alongside the
auxiliary guide.
Sawing with Guide Rail (GKS 85 G) (see figures G–H)
The guide rail 31 is used to carry out straight cuts.
The rubber lip on the guide rail acts as a splinter guard; it pre-
vents fraying of the surface while sawing wooden materials.
For this, the teeth of the saw blade must face directly against
the rubber lip.
Prior to the very first cut, the rubber lip must be adapted with
the guide rail 31 to the circular saw being used. For this, place
the guide rail 31 over its complete length on a workpiece. Ad-
just a cutting depth of approx. 9 mm and the saw blade to a ze-
ro degree angle. Switch the circular saw on and guide it uni-
formly and with light feed in the cutting direction.
Two guide rails can be connected using the connection piece
32. Clamping is carried out with the four screws located in the
connection piece.

Maintenance and Service

Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean. Remove dust and
chips by blowing out with compressed air or with a brush.
Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must
be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts.
Therefore, clean the saw blade immediately after use.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
English | 19
1 609 92A 14V | (10.2.15)