Herunterladen Inhalt Inhalt Diese Seite drucken

Connecting The Power Cord - Pioneer AVH-X8500BT Installationsanleitung

Vorschau ausblenden Andere Handbücher für AVH-X8500BT:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 34
Connecting the units

Connecting the power cord

Navigation system
26 pin cable (Supplied with navigation unit)
(AVIC-F250 (sold
Insert the 26 pin cable in the direction
separately))
indicated in the figure.
Please contact your dealer to
inquire about the connectable
navigation unit.
Note:
Depending on the kind of vehicle,
the function of 2* and 4* may be
different. In this case, be sure to
connect 1* to 4* and 3* to 2*.
2*
1*
4*
3*
Yellow (2*)
Yellow (1*)
Back-up
Connect to the constant 12 V
(or accessory)
supply terminal.
Red (4*)
Red (3*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
Orange/white
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
ISO connector
Note:
In some vehicles, the ISO connector may be divided into
two. In this case, be sure to connect to both connectors.
4 m
This product
Fuse (10 A)
Antenna input
RGB input
AUX jack (3.5 ø)
Use a mini plug
cable to connect
with auxiliary
device.
Connect leads of the same
color to each other.
Speaker leads
White:
Front left
White/black:
Front left
Gray:
Front right
Gray/black:
Front right
Rear left  or subwoofer
Green:
Rear left  or subwoofer
Green/black:
Rear right  or subwoofer
Violet:
Rear right  or subwoofer
Violet/black:
Connecting the units
Microphone
Microphone input
Wired remote input
Hard-wired remote control adapter can be connected (sold separately).
Violet/white
Of the two lead wires connected to the back lamp, connect the one in which the
voltage changes when the gear shift is in the REVERSE (R) position. This connection
enables the unit to sense whether the car is moving forwards or backwards.
Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on
that equipment. If not, keep the Audio Mute lead free of any connections.
Connection method
1. Clamp the lead.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner's Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch.
Blue/white
Connect to system control terminal of the
Power supply side
power amp (max. 300 mA 12 V DC).
Ground side
Blue/white (6*)
Blue/white (5*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO
Notes:
connector will differ depending on
· Change the initial setting of this unit (refer to the Operation Manual).
the type of vehicle. Connect 5* and
The subwoofer output of this unit is monaural.
6* when Pin 5 is an antenna control
· When using a subwoofer of 70 W (2 Ω) , be sure to connect with Violet
type. In another type of vehicle,
and Violet/black leads of this unit. Do not connect anything to Green
never connect 5* and 6*.
and Green/black leads.
Section
01
2. Clamp firmly with
needle-nosed pliers.
Parking brake
switch
3
En

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis