Inhaltsverzeichnis
Werbung
OBJ_BUCH-1050-004.book Page 16 Thursday, April 26, 2012 10:22 AM
16 | English
Technical Data
Straight grinder
Article number
Rated power input
Output power
Max. speed
Thread of grinder spindle
Max. spindle length
Tool holder
Max. grinding disc thickness
Grinding tool diameter, max.
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0.36 ohm.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Helmut Heinzelmann
Senior Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
28.03.2012
Assembly
Before any work on the machine itself, pull the mains
plug.
Mounting the Protective Devices
Adjust protection guards in such a manner that spark-
ing toward the operator is prevented.
Protection Guard for Grinding (GGS 6 S) (see figure A)
Place the protection guard 2 on the spindle collar. Adapt the
position of the protection guard 2 to the requirements of the
work step. Lock the protection guard 2 with locking screw 14
and tighten the locking screw with at least 10 Nm.
Protection Guard for Grinding (GGS 6) (see figure E)
Place the protection guard 11 on the spindle collar. Adapt the
position of the protection guard 11 to the requirements of the
work step. Lock the protection guard 11 with the two locking
nuts 19 and tighten the locking nuts with at least 10 Nm.
1 619 929 K88 | (26.4.12)
GGS 6
0 601 214 0..
W
1200
W
720
-1
min
6800
5/8"
mm
27
mm
16
mm
25
mm
125
kg
3.9
/II
After mounting the grinding tool, shut the protection guard 11
and tighten both wing nuts.
Mounting the Grinding Tools
The grinding tools must run completely concentrically. Do not
continue to use damaged grinding tools that are out of bal-
ance. If the grinding tools are out of balance they should be re-
placed. Treat with a whetstone (accessory) or change.
Using a whetstone, any particular special shape can be pro-
duced out of the basic forms of the grinding accessory.
When using grinding tools with a threaded insert, pay atten-
tion that the end of the grinder spindle 3 does not touch the
hole base of the grinding tool.
GGS 6 S (see figure B)
– Turn the grinder spindle 3 until the hole in the grinder spin-
dle 3 and the openings of the housing are aligned. Insert
the holding rod 15 through the openings of the housing
and the hole of the grinder spindle 3.
– Loosen and remove the clamping nut 1 with the two-pin
spanner 16 provided.
– Clean the grinder spindle 3 and all parts to be mounted.
– Mount the grinding accessory and tighten clamping nut 1
with two-pin spanner 16. Pay attention that the grinding
accessory can rotate freely in protection guard 2.
Use tapered grinding accessories only in conjunction
with the open protection guard 2 and the matching
clamping system (clamping nut 1 and mounting flange
4).
GGS 6 (see figure F)
– Turn the grinder spindle 3 until the hole in the grinder spin-
dle 3 and the openings of the housing are aligned. Insert
the holding rod 15 through the openings of the housing
and the hole of the grinder spindle 3.
– Loosen the clamping nut 9 with the open-end spanner 20
(size 24 mm) by turning in anticlockwise direction.
– Remove the clamping flange 10.
– Clean the grinder spindle 3 and all parts to be mounted.
GGS 6 S
0 601 214 1..
1150
670
6800
M 14
31
20
32
125
3.9
/II
Bosch Power Tools
Werbung
Inhaltsverzeichnis
