Makita DLM380 Betriebsanleitung Seite 10

4. Release the switch button as soon as the motor
starts running. The mower will continue to run until
you release the switch lever. (Fig. 7)
5. Release the switch lever to stop the motor.
6. When not in use, remove the lock key. Store the lock
key in a safe place out of reach of children.
Adjusting the mowing height (Fig. 8)
WARNING:
• Never put your hand or leg under the mower unit when
adjusting the mowing height.
• Always make sure that the lever fits in the groove
properly before operation.
The mowing height can be adjusted in the range of
between 25 mm – 75 mm.
1. Remove the lock key.
2. Pull the mowing height adjusting lever toward A
side. Move it to your desired mowing height level.
Make sure that the pins on the mowing height
adjusting lever fit in the holes and the lever returns
to B side.
NOTE:
• The mowing height figures should be used just as a
guideline, as the state of the lawn or ground may cause
lawn height to be slightly different to the set height
figure.
• Try a test mowing of grass in a less conspicuous place
to get your desired height.
• It is easier to move the mowing height adjusting lever
with holding the tool firmly. (Fig. 9)
Grass level indicator (Fig. 10)
Grass level indicator shows the volume of caught grass.
– When the grass basket is not full, the indicator
floats during mowing.
– When the grass basket is full, the indicator does
not float during mowing. In this case, stop
mowing immediately and empty the basket. After
emptying the basket, clean it so that its
meshwork vents the air.
NOTE:
• This indicator is rough guide. Depending on the
conditions of inside of the basket, this indicator may not
work properly.
ASSEMBLY
WARNING:
• Always be sure that the lock key and battery
cartridge are removed before carrying out any work
on the mower. Failure to remove the lock key and the
battery cartridge may result in serious personal injury
from accidental start-up.
• Never start the tool unless it is completely
assembled. Operation of the tool in a partially
assembled state may result in serious personal injury
from accidental start-up.
Installing the battery cover
WARNING:
• Do not insert the lock key and battery cartridge before
installing the battery cover. Failure to do so may cause
a serious injury.
Install the battery cover completely before operating the
tool to protect the tool and battery cartridge from mud,
dirt, or water.
10
1. Place the battery cover on the tool with aligning the
protrusions on the tool and the holes of the battery
cover. (Fig. 11)
2. Place your hands in the middle of the battery cover
and depress it. (Fig. 12)
3. Before the first operation, check that the pivot point
of the battery cover is assembled properly. To check
it, pull the battery cover locking lever toward yourself
and open the battery cover. (Fig. 13)
Installing the handle (Fig. 14, 15 & 16)
WARNING:
• When installing handles, position the wires so that they
are not caught by anything in between the handles.
1. Loosen the clamping screws (two pcs).
2. Expand the lower handle to its both sides and with it
expanded in that position pivot it backward and then
fit it in the groove in the deck.
3. Tighten the clamping screws on both sides to secure
the lower handle.
4. Raise the upper handle and align the screw holes in
the upper handle with those in the lower handle.
Secure them with the supplied screws, curl washers
and clamping nuts.
NOTE:
• At this time, keep a firm grip on the upper handle so
that it does not drop off your hand.
NOTE:
• Install the upper handle so that the direction of the
upper handle and the power supply cord are positioned
as shown in the figure. (Fig. 17)
Removing or installing the blade (Fig. 18 & 19)
WARNING:
• Always remove the lock key and battery cartridge when
removing or installing the blade. Failure to remove the
lock key and battery cartridge may cause a serious
injury.
• The blade coasts for a few seconds after releasing the
switch. Make sure that the blade has come to a
complete stop.
• Always wear gloves when handling the blade.
1. Put the mower on its side so that the mowing height
adjusting lever is placed on the upper side.
2. To lock the blade, insert a lumber or similar into the
mower.
3. Loosen the bolt counterclockwise with the box
wrench.
4. Remove the bolt, spring washer, flat washer, and
blade in order.
To install the blade, take the blade removal procedure in
reverse.
WARNING:
• Install blade carefully as they have a top/bottom facing.
• Tighten the bolt clockwise firmly to secure the blade.
• Put the blade so that the blade side with a rotational
direction arrow faces outward.
• Make sure that the blade is installed securely.
Installing the grass basket (Fig. 20 & 21)
Remove the lock key.
Raise the rear guard of the mower unit.
Hook the grass basket on the groove of the mower unit.