Saeco Incanto HD8917 Bedienungsanleitung Seite 26

Behaviour
Coffee has too little cream
or is watery.
Coffee is leaking from the
coffee dispensing spout.
Coffee is not hot enough.
The machine grinds the
coffee beans, but coffee does
not come out.
Coffee comes out slowly.
The frothed milk is too cold. Cups are cold.
Milk does not froth.
The filter cannot be activated
as the OK signal (V) is not
displayed.
The filter cannot
activated and the machine
asks for descaling.
The filter does not fit.
22
ENGLISH
Incanto_OTC_EN-IT-DE_Rev01.indb 22
Cause
Grinders are set to a coarse position. Adjust the grinding fineness as described in the "5.3.3
The blend is not right, coffee is not
freshly roasted or is ground too coarse.
The machine must perform the self-
adjustment.
The coffee dispensing spout is clogged. Clean the coffee dispensing spout and its holes using
Cups are cold.
The temperature is incorrectly
regulated.
Water empty.
The brew group is dirty.
The circuit is not primed.
The coffee dispensing spout is dirty.
The machine must perform the self-
adjustment.
Coffee is ground too finely.
The circuit is not primed.
The brew group is dirty.
The machine must perform the self-
adjustment.
The milk carafe is dirty or incorrectly
placed.
The milk carafe dispensing spout has
not been opened correctly.
The milk carafe is incompletely
assembled.
The type of milk used is not suitable
for frothing.
A filter has just been activated.
be The series of 8 filter is completed.
The filter has not been replaced on
time after the AquaClean water filter
signal started blinking.
The filter has not been installed right
away upon 1st usage but after having
brewed approx.100 product (based on
100ml cups).
You need to remove air from the filter. Let air bubbles come out of the filter and empty the
There is water in the water tank.
Action
Ceramic coffee grinder adjustment" chapter.
Change coffee blend or adjust the grinding fineness
as described in the "5.3.3 Ceramic coffee grinder
adjustment" chapter.
Brew a few cups of coffee.
a toothpick.
Warm the cups with hot water.
Adjust the temperature as described in the "5.3.4
Brewing temperature adjustment" chapter.
Fill the water tank and prime the circuit again as
described in the "5.2.1 Water circuit priming" chapter.
Clean the brew group as described in the "7.2.1 Weekly
brew group cleaning cycle" chapter.
Prime the circuit as described in the "5.2.1 Water circuit
priming" chapter.
Clean the coffee dispensing spout and its holes using
a toothpick.
Brew a few cups of coffee.
Change coffee blend or adjust the grinding as described
in the "5.3.3 Ceramic coffee grinder adjustment" chapter.
Prime the circuit as described in the "5.2.1 Water circuit
priming" chapter.
Clean the brew group as described in the "7.2.1 Weekly
brew group cleaning cycle" chapter.
Brew a few cups of coffee.
Warm the cups with hot water.
Clean the carafe as described in the "7.4.3 Weekly
cleaning of the milk carafe components" chapter, and
insert it in the machine as shown in the "6.2 Milk carafe"
chapter, "Inserting phase".
Check that the milk dispensing spout has been correctly
removed as described in the "6.2 Milk carafe" chapter,
"Start up phase".
Check that all the components have been assembled
correctly, as described in the "7.4.3 Weekly cleaning of
the milk carafe components" chapter, "Reassembly phase".
Read the "6.3 Milk- and coffee-based preparations"
chapter.
You have to dispense at least 10 cups (100 ml x cup)
before activating a new filter. Be careful as if you activate
a new filter, the filter counter will increase automatically.
Descale your machine first as described in the "7.5
Descaling cycle" chapter. Thereafter the filter can
be installed as described in the "10.2.1 AquaClean
installation" chapter.
water tank before installing the filter as described in the
"10.2.1 AquaClean installation" chapter.
27/03/15 12:11