Using Advanced Functions; Playing With High-Fidelity Sound; Sound Retriever; Pure Audio - Pioneer PD-30-K Bedienungsanleitung

Using advanced functions

Chapter 5:
Using advanced functions
The functions that can be used differ according to the
type of disc and file. In some cases, some of the
functions cannot be used. See Playback functions on the
right column.

Playing with high-fidelity sound

Sound Retriever

When compressed sound signals are decompressed for
playback, some parts experience dropouts. By setting
the sound retriever function to ON, compensation is
added for those losses, thus producing richer, more
sumptuous sound.
S.RETRIEVER
• Press the S.RETRIEVER button.
Each time the button is pressed, the function
will change as follows: S.RTRV: OFF  S.RTRV: LOW 
S.RTRV: HI  Returns to original status
• The sound retriever function is disabled when the
pure audio function is ON.

Pure Audio

This function disables digital audio output and plays
analog audio with high fidelity. When set to ON, the
display shows no indicators. The factory default
condition is OFF.
• Press the PURE AUDIO button. PURE AUDIO
Press again to turn the function OFF.
• When this function is set to ON and the main unit's
input is switched to SACD/CD, the PURE AUDIO
indicator will light on the front panel. During disc
playback, the front panel display turns OFF.
• When the PURE AUDIO indicator is lighted, any
iPod/iPhone/iPad connected to the main unit will
not be recharged.
Changing the playback area (layer) of
an SACD/CD
Hybrid SACD discs are composed of two layers, an
SACD layer, and CD layer, allowing you to select which
layer you wish to play.
1 Press the SACD/CD button.
SACD/CD
Input changes to SACD/CD.
2 In the stop mode, press the SACD/CD
button.
Each time the button is pressed, the playback alternates
between the CD area and SACD 2 channel area.
Note
• This unit does not support SACD multi-channel
areas.

Adjusting overall display illumination

This unit is equipped with a dimmer function to allow the
display illumination to be adjusted in three levels,
responding to differing levels of ambient lighting. The
factory default is the brightest setting.
• Press the DIMMER button.
Each time the button is pressed it the brightness
cycles through the three levels.
• The dimmer setting cannot be changed when a
disc is playing with the pure audio function ON (see
at left).
• The brightness of the STANDBY indicator does not
change.
Auto power down (automatically sets
power to standby)
This function automatically switches the unit to standby
mode if no signal or switch operation is detected for 30
minutes.
SET UP
1 Press the SET UP button.
2 Change the setting and confirm.
Use the / button to set the function ON
or OFF as desired, then press the ENTER
ENTER
button to confirm.
Note
• This function is disabled when iPod input is
selected.

Playback functions

The functions that can be used differ according to the type of disc and file. In some cases, some of the functions
cannot be used. Check the usable functions on the table below.
1
Function
Fast forward/Fast reverse
Skip function
Direct search
(designate a specific track for playback)
Repeat playback
Random playback
Programmed playback
(Play tracks in a predetermined order)
View disc data
Sound Retriever
Pure Audio
DIMMER
SACD/CD
1 Some functions may not work for some discs or files, even if indicated [] on the table.
2 Also see Playback of CD-R/CD-RW discs on page 12.
3 • AAC files can be played back only on the PD-30.
• Also see Playable file formats on page 12.
4 Also see Playing DSD discs on page 12.
5 This function is enabled only during playback of files recorded on disc.
6 Hybrid SACD discs only.
Disc/file type
SACD CD-DA WMA
2 MP3
CD-R/-RW DSD
3
AAC
  
  
  –
  
  
 
–
  
– – 
  5

6 – –

05
4


–


–

–

–
11
En