Lighting; Normal Operation - Nordica GIULIETTA Gebrauchsanweisung

9. LIGHTING

IMPORTANT: The first time that the appliance is lit, there will be an odour given off (due to the drying of the
adhesives of the junction chord), which disappears after a short use. It must be ensured, in any case, a good
ventilation of the environment. Upon the first ignition we suggest loading a reduced quantity of fuel and slightly
increasing the calorific value of the equipment.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the
following information:
•
the construction materials of the involved products are not homogeneous, as matter of fact there are
simultaneously parts in cast iron and steel.
•
the temperature to which the body of the product is subject is not homogeneous: from area to area, variable
temperatures within the range of 300° C - 500 ° C are detected;
•
during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as
to cycles of intense use or of absolute standstill when season changes;
•
the new appliance, before being considered seasoned has to be subject to many start cycles to allow all
materials and paints to complete the various elastic stresses;
•
in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal
stress, as well as of wet paint. This paint, although during the manufacture it is backed at 250 ° C fo r some
hours, must exceed many times and for a given period of time the temperature of 350 ° C before becoming
completely embedded in the metallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. Make sure that a strong air change is assured in the room where the appliance is installed.
2. During the first starts, do not load excessively the combustion chamber (about half the quantity indicated in
the instructions manual) and keep the product continuously ON for at least 6-10 hours with the registers less
open than the value indicated in the instructions manual.
3. Repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation booklet
concerning maximum load) and, if possible, keep the lighting periods long avoiding, at least in this initial
phase, short ON/OFF cycles.
5. During the first starts, no object should be leaned on the appliance and in detail on enamelled
surfaces. Enamelled surfaces must not be touched during heating.
6. Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding
abrupt heating with excessive loads.
To light the fire, it is suggested using small wood pieces together with paper or other traded lighting means. It is
FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.
Operation with wood :
Open the secondary air control Picture 2, Pos. A , A1), open the thermostat (B , B1), open the ignition control (C),
light up the fire.
After about 10 minutes, when the fire is lighted, close the thermostat (B, B1) and the ignition control (C) and adjust
the combustion course with the controls (A, A1).
The openings for air (primary and secondary) must be opened together just a little (you must open the eventual
butterfly valve placed on the pipe of smokes exhaust). When the wood starts burning, adjust the air for combustion
according to the instructions on paragraph 10.
Never overload the stove (compare the technical table - max. quantity of loadable fuel).
Too much fuel and too much air for the combustion may cause overheating and then damage the stove, as a
consequence some scratches in the lower front part of the stove could happen.
The warranty does not cover the damages due to overheating of the equipment.

10. NORMAL OPERATION

IMPORTANT: due to the fact the door of the hearth has a remarkable size, we suggest you to open the door very
slowly, to avoid the exit of smokes.
For safety reasons the door of the hearth can be opened only for the loading of the fuel. The hearth door
must always remain closed during operation or rest.
Before opening the hearth door, open the ignition control (C), load the fuel, close the door and after about 5 or 10
minutes close the control (C).
With the registers placed on the front of the appliance it is adjusted the emission of heat of the stove. They must be
opened according to the calorific need. The best combustion (with minimum emissions) is reached when, loading the
wood, most of the air for the combustion passes through the register of secondary air.
Never overload the stove (compare the technical table - max. quantity of loadable fuel).
Too much fuel and too much air for the combustion may cause overheating and then damage the stove, as a
consequence some scratches in the lower front part of the stove could happen. The warranty does not cover
the damages due to overheating of the equipment.
22
GIULIETTA – ISETTA-07 – ISOTTA-07 – ISOTTA FORNO – VIOLA – VIOLETTA
1195300 Rev.08 – EN