Measuring Procedure - Exotek instruments MC-60A Bedienungsanleitung

PIN-FREE MOISTURE METERS
WOOD GROUP TABLE
Name Botanical name (Latin)
Pencilwood, virg. Juniperus virginiana
Pericopsis
Pernambuc Caesalpina echinata
Peroba di campos Paratecoma peroba
Peroba rosa Aspidosperma peroba
Persimmon Diospyros virginiana
Perupok Lophoperalum spp.
Phdiek
Pillarwood Cassipourea malonsana
Pine Pinus sylvestris
Pine, Beach- Pinus maritima
Pine, Benguet
Pine, black Pinus nigra
Pine, Caribian Pinus caribea,
polustris,tacda,oocarpa
Pine, Corean
Pine, eastern white Pinus strobus
Pine, Hoop
Pine, Insignis Pinus insignis-radiata
Pine, Klinki
Pine, Loblolly Pinus caribaea, polustris,
tacda, oocarpa, risida
Pine, Lodge pole
Pine, long-leaf
Pine, Merkus
Pine, Mindro
Pine, Parana Araucaria angustifolia
Pine, Pitch, Honduras Pinus-palustris-tacda-oocarpa-
risida
Pine, Red-, Honduras, Pinus caribaea, polustris,
tacda, oocarpa, risida
Pine, short-leaf Pinus caribaea, polustris,
tacda, oocarpa, risida
Pine, Siberian red
Pine, Slash
Pine, sugar
Pine, Swisse Pinus cembra
kg/m³ Setting
460
750
850
690
710
780
490
630
1000
480
480
570
560
630
460
380
470
440
410
520
430
630
650
650
500
630
520
540
430
630
370
450
- 44 -
PIN-FREE MOISTURE METERS
MANUAL
Material setting:
200 Balsa, Sugi
400
300 Aspen, Cypress, Cedar
700
400 Fir, Poplar, Pine, Alder, Small Leaved
800
Lime tree,
600
500 Maple, Larch, Douglas Fir
700
600 Oak, Birch, Beech, Pear, Teak
700
700 Silver Birch, Hickory, Wengé
400
800 Stone Oak, Zebra
600
900 Boxwood, Rosewood
900
1000 Ebony
400
E1 Breezeblock
400
E2 Plaster, Gypsumboard, walltiles, brick
500
E3 Anhydrite, Floor covering, Clinker,
500
sand, Asbestos
600
E4 Concreet, Cement screed
E5 Marble
400
300
For a wider selection of wood materials, please see the Wood Group
400
Table at the end of the manual.
400

MEASURING PROCEDURE

400
After selecting the appropriate material-group the unit must be hold up in
500
the air for automatic 0-correction. After about 2 sec. "- 00.0" is displayed
and the unit ready for measuring.
400
Hold the spring electrodes without excessive force and in a approx.
600
40 angel to the material.
o
600
All of the 3 measuring springs must
600
be in good contact with the material
400
to be measured.
600
After approx. 2
measuring value is being achieved.
500
This is confirmed with a minus sign " − "
at the left side of the display.
500
Measurements may be taken in different spots of the material, or the
measuring springs could be slided across the material.
400
600
THIN MATERIALS
300
For single materials, thinner than 10 mm, the sensitivity of the meter is
400
normally not enough. However, comparing measurements to determine
MC-60A
sec. a constant
- 5 -
40 Degrees
ENG