Normal Operation - Nordica INSERTO 80 Anweisungen

INSERTO 50 – 80 – 100
To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting
means.
It is forbidden to use any liquid substance as for ex. alcohol, gasoline, oil and similar.
You should place a little quantity of fuel and also open the primary air register (left lever completely pulled
out, pict. 1-1A) and that of secondary air (right lever completely pushed, pict. 1-2A)
When wood starts to burn, it is possible to feed it again by opening slowly the door, in order to avoid leaks
of smoke, and close the primary air register (completely pushed) and control the combustion through the
secondary air register according to the provisions of CHAP. 12.
Please always be present during this phase.
Position the lever of the smoke valve back to the right (all closed).
Never overload the appliance (see the technical table - max. quantity of fuel that can be loaded / hourly
consumption – (see CHAP. 18).
overheating and therefore damage the same.
Never switch on the device when there are combustible gases in the room.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to
know the following information:
•
the construction materials of the involved products are not homogeneous, in fact there are
simultaneously parts in cast iron, steel, refractory material and majolica;
•
the temperature to which the body of the product is subject is not homogeneous: from area to area,
variable temperatures within the range of 300° C - 500 ° C are detected;
•
during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as
well as to cycles of intense use or of absolute standstill when season changes;
•
the new appliance, before being considered seasoned has to be subject to many start cycles to allow
all materials and paints to complete the various elastic stresses;
•
in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal
stress, as well as of wet paint. This paint, although during the manufacture it is backed at 250 ° C for
some hours, must exceed many times and for a given period of time the temperature of 350 ° C before
becoming completely embedded in the metallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1) Make sure that a strong air change is assured in the room where the appliance is installed.
2) During the first starts, do not load excessively the combustion chamber (about half the quantity
indicated in the instructions manual) and keep the product continuously ON for at least 6-10 hours with
the registers less open than the value indicated in the instructions manual.
3) Repeat this operation for at least 4-5 or more times, according to your possibilities.
4) Then load more and more fuel (following in any case the provisions contained in the installation booklet
concerning maximum load) and, if possible, keep the lighting periods long avoiding, at least in this initial
phase, short ON/OFF cycles.
5) During the first starts, no object should be leaned on the appliance and in detail on enameled
surfaces. Enameled surfaces must not be touched during heating.
6) Once the «break-in» has been completed, it is possible to use the product as the motor of a car,
avoiding abrupt heating with excessive loads.
12.

NORMAL OPERATION

The nominal power of the appliance is of:
6 kW INSERTO 50 / 9 kW INSERTO 80 / 9.5 kW INSERTO 100.
This power will be reached with a minimum depression in the chimney of 10 Pascal (=1.0 mm of water
column). With the registers located on the front of the appliance, it is possible to adjust the heat emission of
the same. They have to be opened according to the calorific need. The best combustion (with minimum
emissions) is reached when, by loading the wood, most part of the air for combustion flows through the
secondary air register. On the contrary by loading brown coal brickets the air combustion flows through the
primary air register.
Never overload the appliance (see the hourly wood load in the table here below). Too much fuel and
too much air for the combustion may cause overheating and then damage the stove.
Instructions for installation, use and maintenance
Too much fuel and too much air for combustion can cause
Rev.01
- EN
29