Seite 2
ANY phono cartridge ! To achieve the full performance and to avoid any damages of this tonearm, please take the TT 3 time to get familiar with your Clearaudio tonearm TT 3 - Your Clearaudio tonearm will give you many years of musical enjoyment and pleasure.
14 – 25 Contents 1. Scope of delivery 2. Mounting the tonearm base 3. TT 3 set - up 4. TT 3 adjustment 5. Special instructions / Service 6. Technical data Warranty information Seite / Page 3 clearaudio electronic GmbH 2014...
Please check the contents as shown in the picture below. Important note : TT 3 Please take special care of the tonearm cable while unpacking your Clearaudio- tonearm ! Note: all windings are metrical ! Pic.1: Tonearm parts...
TT 3 User manual / Bedienungsanleitung 2. Mounting the tonearm base Mounting the tonearm base on a Clearaudio turntable: Mount the tonearm base (see picture 2) with the three screws and the hex key wrench (#3) onto the tonearm mounting platform.
Do this until the threaded bolt in the middle between the two drills of the tonearm fully rests in the drilling of the tonearm base. Pic.5: Placing the tonearm on the tonearm base Seite / Page 6 clearaudio electronic GmbH 2014...
Seite 7
After passing the first main rod, turn the headshell back (as shown in pic. 9) Positioning shaft Pic.7: Setting up the headshell Pic.8: Turning the headshell Pic.9: Turning the headshell back Pic.10: Correct position of the headshell Seite / Page 7 clearaudio electronic GmbH 2014...
Please take care of the colour codes. Red: right channel / R+ Green: right channel / R- White: left channel / L+ Blue: left channel / L- Adjust little pressure. The exact pressure will be adjusted later Seite / Page 8 clearaudio electronic GmbH 2014...
Seite 9
To achieve the right height of the cartridge you can move the tonearm by turning the VTA screw on the top of the tonearm (shown in picture 14). Pic.14: Height adjustment Seite / Page 9 clearaudio electronic GmbH 2014...
Seite 10
Pic.16 b: Adjustment of the tonearm`s tilt angle Adjust the correct stylus pressure as instructed in the cartridge´s user manual. To achieve the exact stylus pressure we recommend the use of the clearaudio digital stylus pressure gauge “Weight Watcher” (Art.-#: AC 094; also available at www.analogshop.de).
Seite 11
(Azimuth) of the cartridge. Lock this screw again after your adjustments are finished. The following step will ensure real linear tracking. You will need the delivered Clearaudio linear gauge for this adjustment. Place the gauge over the spindle of the platter and turn it under the chassis of the tonearm.
User manual / Bedienungsanleitung 5. Special Instructions / Service Please take the time to fill out the enclosed warranty card and return it to Clearaudio or your local distributor / dealer. If you do not return this card within 14 days after purchase the guarantee will only be for the law regulated guarantee time period.
Approx: 260 mm x 50 mm x 100 mm Warranty: 5 Years* (see chapter 5 / page 26) * Only if the warranty card is filled out correctly and sent back to Clearaudio within 14 days. Attention: This tonearm is suitable for cartridges from 7 gr. net weight! If your cartridge is easier, please use an additional weight (headshell plate).
TT 3 User manual / Bedienungsanleitung Sehr verehrte clearaudio – Kundin, sehr verehrter clearaudio - Kunde, Wir gratulieren Ihnen! Sie haben sich für einen der besten Tonarme, den neuen clearaudio TT 3 - Tangentialtonarm entschieden. Ein erstklassiges, in aufwändiger Handarbeit gefertigtes Produkt der clearaudio electronic GmbH.
Seite 15
User manual / Bedienungsanleitung Inhaltsverzeichnis 1. Lieferumfang 2. Befestigung der Tonarmbasis 3. Aufsetzen des TT 3 - Tonarms 4. TT 3 Einstellungen 5. Wartung und besondere Hinweise 6. Technische Daten Garantiebedingungen Seite / Page 15 clearaudio electronic GmbH 2014...
Tonarm angepasste Verpackung, die einen sicheren Transport garantiert. Bitte bewahren Sie diese Verpackung für den Fall eines Transports auf. TT 3 Bitte kontrollieren Sie den Lieferumfang Ihres neu erworbenen clearaudio Tangentialtonarms. TT 3 Achten Sie vor der Entnahme des clearaudio –...
TT 3 User manual / Bedienungsanleitung 2. Befestigung der Tonarmbasis Montage der Tonarmbasis auf einem clearaudio Laufwerk: Befestigen Sie die Tonarmbasis auf dem sauberen Untergrund des Laufwerkchassis mit den drei mitgelieferten Innensechskantschrauben (Siehe Abb. 2 unten) und dem passenden Inbusschlüssel (Größe 3). Achten Sie auf passgenauen Sitz und planebene Montageflächen.
Führungsbohrungen auf die Trägerstäbe der Tonarmbasis auf und schieben Sie den Tonarm so weit auf die Trägerstäbe, bis der mittlere Gewindestab vollständig in der Bohrung des Tonarmbasis versinkt. Abb.5: Aufsetzen des Tonarms Seite / Page 18 clearaudio electronic GmbH 2014...
Seite 19
Danach drehen Sie das Headshell wieder in die Ausgangsposition (siehe Abbildung 9). Abb.7: Einsetzen des Headshells Positionsstift Abb.8: Position nach Einsetzen des Headshells Abb.9: Position nach Einsetzen des Headshells Abb.10: Korrekte Position des Headshells (Oben-Ansicht) Seite / Page 19 clearaudio electronic GmbH 2014...
Weiß: linker Kanal / L+ Blau: linker Kanal / L- Setzen Sie den Tonabnehmer durch Betätigen des Lifthebels an der Seite des Tonarms vorsichtig auf die LP oder die Einstellschablone auf. Seite / Page 20 clearaudio electronic GmbH 2014...
Um die Höhe Ihres Tonarmes zu verstellen, lösen Sie bitte zuerst die Inbusschlüssel auf der Seite des Tonarms. Drehen Sie dann die Rändelschraube auf der Oberseite des Tonarms (siehe Abbildung 14) in die Abb.14: Höhenverstellung jeweilige Richtung. Seite / Page 21 clearaudio electronic GmbH 2014...
Stellen Sie die korrekte Auflagekraft Ihres Tonabnehmers laut der Herstelleranleitung ein. Zur Einstellung der korrekten Auflagekraft empfehlen wir die digitale Tonabnehmerwaage „Weight Watcher“ von clearaudio (Art.: AC094; auch erhältlich über www.analogshop.de). 4.3 Einstellung des Azimuth (Vertikale Position des Tonabnehmer - Diamanten in der Rille) Bitte gehen Sie in dem folgenden Schritt äußerst vorsichtig vor!
Seite 23
Vor dem erstmaligen Benutzen oder nach längerem Stillstand müssen Sie den Lift ca. 4-5 x betätigen, damit sich das Fett im Tonarmlift lösen kann und die Liftbank gleichmäßig und ordnungsgemäß abgesenkt werden kann. TT 3 Der clearaudio - Tonarm ist nun komplett justiert und spielbereit. Seite / Page 23 clearaudio electronic GmbH 2014...
5. Wartung und besondere Hinweise Bitte senden Sie die beigelegte Garantiekarte innerhalb von zwei Wochen korrekt ausgefüllt an clearaudio zurück, da sonst nur die gesetzliche Garantiezeit von 2 Jahren bestehen würde. Die Einstellung der Saphirlagerschrauben im Wagen auf keinen Fall verändern, sie sind ab Werk optimal justiert and anschließend gesichert worden.
Abmessungen (B*H*T) in mm: Ca. 260 mm x 50 mm x 100 mm Garantie: 5 Jahre* (siehe Kapitel 5 und Seite 26) * nur bei korrekt ausgefüllter und innerhalb von 14 Tagen an clearaudio eingesandter Garantiekarte. Bitte beachten: Dieser Tonarm ist für Tonabnehmer ab 7 gr. Eigengewicht geeignet! Sollte Ihr Tonabnehmer leichter sein, benutzen Sie bitte zusätzlich ein Gewicht...
RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with clearaudio. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is adequate for such proof.