Technical Data; Safety Instructions; Safety - WOLFF CT 200 Originalbetriebsanleitung

1.0 Technical data

1.1 Milling machine
Width of cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mm
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 cm
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 cm
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 cm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 kg
Dust port diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 mm
Height adjustment . . . . . . . . . . . . . . . . . .Hand wheel and lever
Electric motor . . . . . . . . . . . . . . .230 V, 2.2 kW (400 V, 3.0 kW)
Honda petrol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5 PS
Other Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .On request
1.2 Tools
Drum diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 mm
Cutter shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 mm
Number of cutter shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
TCT cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46/5
Milling cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46/20
Beam flails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Cutter diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 mm
Number of TCT cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Number of milling cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
All specifications are approximate and subject to confirmation.

2.0 Safety instructions

While operating the machines the following points should also
be kept in mind:
The machine should always be operated with all safety
covers and technical precautions.
Never leave the machine during operation.
Before leaving the machine all rotary parts should be
brought to a stand still. The electric models must be
disconnected from the mains. Make sure that the machine
cannot roll or move by itself.
After maintenance and adjustment all safety covers must
be reattached.
If noise level exceeds 90 dB(A) ear protectors must be worn.
For your own safety, always use ear protectors.
In the event of a large amount of dust ding operation
connect a dust collector to the machine

3.0 Safety

Disconnect the power supply before any maintenance is carried
out. Use only recommended tools and ensure it is fastened
before starting.
Maintenance should be undertaken only by qualified personnel.
Use only genuine Wolff spare parts.
01/2002 FugBodenfräse CT 200enfräse #013641
Comes with:
CT 200
Tools
Ear protection
Goggles
Operation manual
The CT 200 milling machines are constructed according
to existing safety rules and regulations. These technical
precautions should not be removed or changed under
any circumstances.
9