Technical Data; Maintenance And Cleaning - VOLTCRAFT PB-9 Bedienungsanleitung

6. Remove the product from the USB power source when the display shows a full battery
(100 %) or when it has already turned off. The device is fully charged and ready for use.
It takes about 10 hours to fully charge the battery at an input current of 1.8 A. The actual
charging time required depends on the battery level and the charging current used.
If you only use the product occasionally, we recommend that you fully charge the
internal battery every three months in order to retain maximum capacity.
Smart charging: The power bank features advanced smart charging technology in order
to accommodate the charging current used. The charging current used can vary from
500 mA to 1800 mA.
c) Charging a mobile device
Press the multifunction button (2) to display the battery level of the power bank.
Charge the power bank before starting to charge a mobile device if the battery level
is insufficient.
1. Connect the micro USB plug to the micro USB port on your mobile device.
2. Connect the USB-A connector on the USB cable to the USB-A port OUT 5 V / 1A (3) or
USB A port OUT 5 V / 2.1A (5) on the power bank. Pay attention to the technical data for
the mobile device you are going to charge. If necessary, you can connect a second mobile
device for charging to the second USB-A port.
3. Press the multifunction button to begin charging. The LEDs on the battery level display (1)
light up when charging begins. They indicate the remaining capacity of the power bank.
The battery level display turns off after about 15 seconds.
4. The LEDs in the USB A port light up. Only the LED on the active side stays on; the LED on
the inactive side goes off after a few seconds. To display the battery level at a later time for
a few seconds, briefly press the multifunction button (2).
5. Monitor the charging process. Charging cannot be interrupted using the multifunction
button. If you want to interrupt the charging process, remove the USB cable from the
mobile device.
You can re-establish the USB connection within 15 seconds to immediately resume
charging the mobile device. After 15 seconds have expired, this quick change is
no longer possible. The multifunction button must be pressed again to restart the
charging process.
6. The power bank turns itself off after about 30 seconds when the battery in the mobile
device is fully charged. It also turns off when the USB cable is disconnected.
7. Remove the USB cable from the product and the mobile device after charging is complete.
The LEDs in the USB A ports turn off.
It is not possible to charge the power bank whilst using it to charge a mobile device.
d) Flashlight function
A built-in LED (6) enables you to use the product as a flashlight.
1. Press the multifunction button (2) twice in succession to turn on the flashlight. The LED
turns on.
2. Press the multifunction button twice in succession to turn off the flashlight. The LED turns
off.
e) Overload protection
The LEDs in the USB ports (3, 5) blink if there is an overload. The device turns off
automatically after a short period. Remove the connected device and reset the power bank
by recharging it using the power source. Press the multifunction button to resume charging. If
there is still an overload, the LEDs will flash again.

MAINTENANCE AND CLEANING

Never use aggressive detergents, rubbing alcohol or other chemical
solutions, as these could damage the housing or even impair the
functioning of the product.
• Disconnect the USB cable and your connected mobile device from the product before
cleaning.
• Do not immerse the product in water.
• Under no circumstances should you service any of the components in the interior of the
product, therefore never open/dismantle it.
• A dry, soft and clean cloth is sufficient for cleaning. Do not press too hard on the housing as
this can lead to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
DISPOSAL
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
The built-in battery must be removed by a specialist before disposal.
b) Rechargeable batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/
rechargeable batteries; disposal of them in the household waste is prohibited!
Contaminated rechargeable batteries are labelled with this symbol to indicate that
disposal in the domestic waste is forbidden. The designations for the heavy metals
involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on rechargeable
batteries, e.g. below the trash icon on the left).
Used rechargeable batteries can be returned to collection points in your
municipality, our stores or wherever rechargeable batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

TECHNICAL DATA

Input voltage / current ...........................5 V/DC, 0.5 to 1.8 A
Output voltage / current ........................ Output 1: 5 V/DC, max. 1 A
Internal rechargeable battery ................Lithium-ion (Li-Ion) 3.7 V/DC / 15000 mAh
Bulb ......................................................LED, 1 x 50 mW
Operating conditions .............................0 to +45 °C, 10 - 85 % RH
Storage conditions ................................-10 to +60 °C, 10 - 90 % RH
Dimensions (W x H x D) .......................151 x 22 x 77 mm
Weight ..................................................347 g
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the
time of printing.
© Copyright 2014 by Conrad Electronic SE
Output 2: 5 V/DC, max. 2.1 A
V1_1214_02-DS