Stromkabel prüfen Die Isolierung des Stromkabels muss einwandfrei und ohne Risse sein. Bitte wenden Sie sich im Zweifelsfall an Ihren Elektro-Fachmann oder an einen RENNER-Händler in Ihrer Nähe. Etwaige Verlängerungskabel müssen dieselben Maße aufweisen wie das am Kompressor montierte Kabel.
Kompressors bestehen. Bei fehlender Übereinstimmung kann der Kompressor überlastet werden. 2.3 Betriebsdauer Die Modelle für Hobby und Handwerk sind für einen kurzzeitigen Betrieb konzipiert und somit nicht für längere zusammenhängende Betriebszeiten oder gar Dauerbetrieb ausgelegt. Eine Nichtbeachtung kann die Anlage beschädigen und sich negativ auf den Garantieanspruch auswirken.
Fragen zu Atmungsgeräten sind an RENNER zu richten. 3.5 Transport von Kompressoren Bei Transport von Kompressoren mit einer “Produktzahl”, die 1000 = Fassungsvermögen x max. Behälterdruck übersteigt, ist der Behälter erneut zu genehmigen (gilt nicht für den Transport von RENNER an den Verwender).
(Ablassschraube im Behälterboden). Der Luftfiltereinsatz sollte je danach, wieviel Staub im Umfeld des Kompressors anfällt, regelmäßig ausgewechselt werden. 4.2 Öltyp Nur genehmigtes vollsynthetisches Kompressoröl einsetzen. empfehlen RENNER-Kompressorenöl Art.-Nr.: 15143-1. Gebrauch eines handelsüblichen Motoröls können wichtige Teile des Kompressors zerstört werden.
5 Fehlersuche und Abhilfe Störung Ursache Abhilfe Der Kompressor scheidet Öl durch Zu hoher Ölfüllstand am Kompressor Geringfügig Öl ablassen, bis das Entlüfterrohr aus Ölschauglas zur Hälfte gefüllt ist Bei Stillstand des Kompressors Verschmutztes Rückschlagventil Rückschlagventil reinigen oder strömt ständig Luft aus dem Gummidichtung tauschen Druckregler heraus Starkes Geräusch am Kompressor...
EG-Konformitätserklärung Der Hersteller / Inverkehrbringer RENNER GmbH Kompressoren Emil-Weber-Straße 32 74363 Güglingen erklärt hiermit, dass folgendes Produkt Produktbezeichnung: RENNER Kolbenkompressor Fabrikat: RENNER Seriennummer: Serien-/Typenbezeichnung: REKO Beschreibung: Kolbenkompressor zur Erzeugung von Druckluft von 8 bis zu 15 bar allen einschlägigen Bestimmungen der oben genannten Richtlinie sowie den weiteren angewandten Richtlinien (nachfolgend) - einschließlich deren zum Zeitpunkt der Erklärung geltenden Änderungen - entspricht.
8 Technische Daten Ansaug- Eff. Nenn- Max. Schall- Druckluft- Abmessungen Spannung Zylinder / Drehzahl Modell leistung Liefer- leistung Druck pegel behälter L x B x H wicht Volt Stufen U/min l/min menge dB(A) Liter REKO 235W/24 2800 600x330x640 REKO 250W/10 2800 390x310x640 REKO 270W/40...
Seite 11
Table of contents Before operating the machine ................12 Safety.............................. 12 Function, use and operation time ..............13 Function ............................13 Use ..............................13 Operation time ..........................13 Operation ......................14 Placement ............................14 Start/stop-procedure ........................14 Pressure regulation ........................14 Limitation of use ..........................
This chapter informs you about basic advice as to the safe handling of the compressor. Before operating the machine you should carefully inspect the machine in order to find possible missing parts or damages. Please report anything which is not satisfactory, to your local RENNER dealer. 1.1 Safety Cable inspection The isolation on the cable must be free, flawless, and without cracks.
If there is a disharmony the compressor can be overloaded. 2.3 Operation time The models for hobby and craft are designed for short-term operation, and thus not designed for longer continuous operation time or even uninterrupted service.
3.4 Limitation of use The compressor cannot directly be used for respiration purposes. The air in the compressor is not clean enough. If questions regarding compressed air for respiration should appear please contact RENNER GmbH. 3.5 Transport of compressors At the transport of compressors with a product of over 1000 = capacity x max. receiver pressure, the receiver...
4.2 Oil type Only use approved full synthetic compressor oil. We recommend the RENNER compressor oil 68, item-nr.: 15143-1. If using ordinary motor oil vital parts of the compressor can be damaged. 4.3 Environmental demands When changing oil it is not allowed to discharge the oil directly on the ground.
5 Troubleshooting Error Cause Repairment The compressor leaks oil Oil level is too high Remove oil through plug till oil glass is half full Air is continiously leaking from Dirt in the bypass valve Clean the bypass valve or repplace pressure switch when the rubber fitting in the bypass valve compressor is stopped...
EC Declaration of Conformity The manufacturer / distributor RENNER GmbH Kompressoren Emil-Weber-Straße 32 74363 Güglingen hereby declares that the following product Product description: RENNER Piston compressor Manufacturer: RENNER Serial no.: Series / type description: REKO Description: Piston compressor for generating compressed air of 8 to 15 bar meets all relevant provisions of the above stated guideline and the other applied guidelines (to follow) - including the changes applicable at the time of the declaration.
8 Technical data Stroke Nominal Max. Sound Receiver Dimensions Voltage Cylinders Weight Model volume power press level capacity LxBxH deliv. Volt / stages U/min l/min dB(A) Litre REKO 235W/24 2800 600x330x640 REKO 250W/10 2800 390x310x640 REKO 270W/40 1400 730x400x680 REKO 270W/25 1450 430x690x790 REKO 320W/24...