Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Manual URYXXON
13.4.2. Edit worklist
As for every sample, you can edit the worklist entries and add
additional information as well. To do so, press on an ID in the
worklist, or choose an ID via the scroll-arrows
. The edit screen for measurements appears and you can
Edit
selected
add or edit ID, Seq.No., clarity and colour, respectively (see Cus-
tomization, chapter 8.8).
Edit next sample
Id
55875410
Clarity
clear
Color
yellow
Delete
The activity-button
Delete
worklist. If you press
Skip
of the list.
Note: You can only edit information for samples, as long as they
are in the worklist. Therefore, always edit samples before you
place the respective strip on the transport tray. As soon as the
strip has been drawn into the housing, the data cannot be edited
anymore.
13.4.3. Measuring with the worklist
When you measure with the worklist, patient IDs are already set
for every sample. The sample's ID which will be measured next
is always in the left side of the start screen under ID.
Dip the test strip into the sample. To start measuring, place the
test strip on the left side of the instrument onto the black trans-
port tray. The light briefly flashes green, thus indicating automatic
strip detection. Right after, the transport rack moves to take the
strip into the instrument. During that time, the light is red, be-
cause no other strip can be placed while the strip is drawn into
the housing. The measurement of the strip is automatic.
Make sure to always place the strips onto the transport rack in
the order corresponding to the worklist entries. Once the strip
has been drawn in, a new sequence number appears and the ID
on the left side is replaced with the first ID from the worklist on the
right. The worklist on the right moves up by one entry.
If necessary, add supplemental information and place the next
strip onto the transport rack. Thus, you can work your way to the
end of the list.
Within a worklist, you cannot change the sequence numbers,
since the individual measurements are pre-defined by the entries
in the worklist.
Note: It is very important to place the strips onto the transport
rack according to the order defined by the worklist, so that the
correct strips will be measured for displayed ID.
50
500
®
Seq.No.
0012
cloudy
dark
turbid
None
red
brown
other
None
Skip
allows you to delete an entry from the
, the entry will be placed at the end
13.4.4. Options
On the right side of the screen underneath the worklist, you
can find the activity-button
and press
choices.
13.4.4.1. Load list
The activity-button
worklist from your LIS (see Create a worklist, chapter 13.4.1).
13.4.4.2. Print list
The activity-button
worklist, including the respective sequence number and supple-
mental information. Press the button to start printing.
13.4.4.3. Delete list
The activity-button
list irrevocably. In order to delete the list, press the activity-button
Delete worklist
. The results of samples from the worklist that have al-
ready been measured remain in the instrument's memory.
13.4.5. Emergency measurement
You can expedite an emergency measurement while you are
working with a worklist. Press the activity-button
lower left part of the screen. The menu for patient and sample in-
formation appears, and you can enter patient ID, etc. The new ID
is placed as the next sample in the left part of the screen, while
the other samples all move back one position. Then, perform the
measurement as usual.
. These options include three
Options
Menu
Insert strip
Next sample
Worklist
ID
55674276
55816478
55156472
Seq.No.
55684123
0001
Load worklist
55741836
Clarity
55412754
clear
Print worklist
55971287
Color
Delete worklist
yellow
55147528
Edit
Emergency
Options
allows you to load an existing
Load worklist
allows you to print all IDs in the
Print worklist
removes all entries in the work-
Delete worklist
and confirm the following security question with
Manual URYXXON
®
500 V 01 / 03.10
15 10
BLD
UBG
BIL
PRO
Edit
NIT
selected
KET
GLU
pH
in the
Emergecy
MN
Werbung
Kapitel
Inhaltsverzeichnis
