Customized Order; Interface; Hw Settings; Baud Rate - MACHEREY-NAGEL URYXXON 500 Handbuch

Manual URYXXON

8.1.2. Customized order

The option-field
Customized order
order of the parameters when results are printed and displayed.
By default, the order is identical to the order of the test pads on
the URYXXON ® Stick 10 and the choice button
If you want to change the order, press the choice button
adjacent activity field
Edit
a new menu appears, displaying the existing parameters. Along-
side are scroll-buttons
The current order of the parameters is displayed on the right half
of the screen.
Customized order
BLD
UBG
BIL
PRO
NIT
KET
GLU
pH
Select
To change the orders of parameters, press the activity-button
in the lower part of the screen. The current order disap-
Clear
pears and only the number 1: remains.
By pressing the parameters on the right side of the screen you
can define a new order for all parameters. You can pick the pa-
rameters either by pressing the parameter directly, or by scrolling
through the list using the scroll-buttons
activity-button . Parameters that have already been se-
lected are not available anymore. They are listed on the right side
of the screen with a preceding position number.
Customized order
BLD
UBG
NIT
KET
GLU
pH
Select
Customized order
Select
If you are not satisfied with your selection; press
selection on the right hand side is discarded and you can enter
your personal order again.
Press to confirm and save your changes. If you leave the
menu by pressing , none of your choices will be adopted.
38
500
®
enables you to change the
is enabled.
Off
is activated. Once you can press it,
to reach all parameters in the list.
1: BLD
2: UBG
3: BIL
4: PRO
5: NIT
6: KET
7: GLU
8: pH
9: SG
10: LEU
Clear
and pressing the
1: PRO
2: BIL
3: LEU
4: SG
Clear
1: PRO
2: BIL
3: LEU
4: SG
5: BLD
6: pH
7: UBG
8: NIT
9: GLU
10: KET
Clear
Clear

8.2. Interface

In the Interface menu you can change the interface settings.
Note: Changes in the interface settings directly influence data
transfer. This is especially important when the instrument is con-
nected to a LIS.
. The
On
You can decide whether the interface communication should be
uni- or bidirectional. To do so, press the respective choice-but-
ton in the option-field. Press
changes. If you leave the menu by pressing
choices will be adopted.
Note: If bidirectional communication is enabled, the receiver has
to be configured in the same way. If this is not the case the device
will report a transmission error.

8.2.1. HW settings

In the HW settings menu, you can carry out additional hardware
adjustments. Once you press the activity-button
new menu with multiple option-fields appears. Within the menu,
the bold values show the default settings.
Baudrate
Bitlength
Parity
Press to confirm and save your changes. If you leave the
menu by pressing

8.2.1.1. Baud rate

You have five different choices for the baud rate (1200, 2400,
4800, 9600, 19200). Press the respective choice-button to
change the baud rate.

8.2.1.2. Bit length

You have two different choices for the bit length (7 Bit / 8 Bit).
Press the respective choice-button to change the bit length.
. The
Interface
Interface settings
Undirectional Bidirectional
HW settings
to confirm and save your
HW settings
1200 2400 4800 9600
7 bit 8 bit
None Even Odd
, none of your choices will be adopted.
Manual URYXXON ® 500 V 01 / 03.10
, none of your
, a
HW settings
19200
MN