Part Names And Functions; Deck Section - Pioneer DDJ-S1 Bedienungsanleitung

8 ON/OFF switch
Turns this unit's power on and off.
9 DC IN terminal
Connect to a power outlet using the included AC adapter (with the
power plug mounted).
Wait until connection of all equipment is completed before con-
necting the AC adapter.
Only use the included AC adapter.
a Cord hook
Catch the AC adapter's power cord and USB cable on this hook
when using this unit.
The sound will be interrupted if the AC adapter or USB cable is
disconnected during playback.
 Cord hook
Hook the AC adapter's power cord in the top of the cord
hook, the USB cable in the bottom.
Fasten the AC adapter's power cord and USB cable in place by hooking
them on the cord hook. This prevents the power cord and USB cable
from being accidentally pulled and the plugs from being disconnected
from the terminals.
The sound will be interrupted if the AC adapter or USB cable is
disconnected during playback.
AC adapter's power cord
USB ON OFF DC IN
USB cable
Upper left of control panel
Microphone
or
OFF ON
LOAD CRATES
MIC 1 A
EQ
LEVEL LOW MID HI
INST.DOUBLES
TALK
OFF ON OVER FX CH S
B
A
MIC 1 MIN MAX MIN MAX MIN MAX MIN MAX
HOT CUE
VINYL
DELETE
SPEED ADJUST
EFFECT
1
2
NEEDLE SEARCH / ALPHABET SEARCH
PARAM
JOG MODE
1 MIC1 terminal
Connect a microphone here.
Using a microphone (p.28)
Either an XLR connector or a phones plug (Ø 6.3 mm) can be
used.
5 V
Cord hook
OFF ON
MIC 1
LEVEL LOW
TALK
OFF ON
OVER
MIC 1
MIN MAX MIN MAX MIN
1

Part names and functions

Deck section

MIC 1
m
HOT CUE
DELETE
l
k
j
i
REC MODE
h
g
SHIFT
CUE
PLAY/PAUSE
f e
1 Playing address indicator
The position in the track is displayed in 10 steps, with the beginning
of the track at the left edge, the end of the track at the right edge. The
indicator lights in sync with the elapsed playing time or remaining
time display in the "ITCH" software.
2 LOAD (INST. DOUBLES) button
The selected tracks are loaded to the respective decks.
Loading tracks to decks (p.22)
When the [LOAD (INST. DOUBLES)] button is pressed while press-
ing the [SHIFT] button, the track being played is doubled.
EQ
MID
Instant Doubles (p.22)
3 NEEDLE SEARCH (ALPHABET SEARCH) pad
The sound is played from the position at which the pad is
touched.
The alphabet search function can be used.
Searching using the [NEEDLE SEARCH (ALPHABET SEARCH)]
pad ("Alphabet Search") (p.20)
4 VINYL SPEED ADJUST control
For track playing and stopping, this adjusts the speed at which play-
back slows until it stops and the speed at which the normal playback
speed is reached from the stop mode.
5 LOOP SELECT (GRID LOCK) button
The loop you want to play can be selected from the loops that have
been pre-registered in the loop bank.
The loop bank number switches each time the button is pressed.
Using the loop bank (p.24)
When the [LOOP SELECT (GRID LOCK)] button is pressed while
pressing the [SHIFT] button, the overall beat grid is locked so that it
cannot be edited.
6 VINYL (ILLUMINATION) button
This switches the [VINYL] mode on/off.
Switching the jog dial mode (p.22)
7 AUTO LOOP (GRID SLIDE) control
This sets auto loops.
1
OFF ON
MIC 1
EQ
LEVEL LOW MID
TALK
OFF ON
OVER
MIN MAX MIN MAX MIN MAX MIN
1
2
NEEDLE SEARCH /
ALPHABET SEARCH
LOOP/ GRID
IN OUT RELOOP / EXIT SELECT AUTO
3
1/ 2X
4
SET TAP CLEAR LOCK SLIDE
REV
5
REV FWD
PHONES
d c
2
LOAD
A
HI
INST.DOUBLES
3
MAX
VINYL
SPEED ADJUST
4
5
JOG MODE
6
VINYL
ILLUMINATION
7
2X
TEMPO
RANGE
8
SLIP MASTER
TEMPO
9
a
b
0
SYNC
TEMPO
SYNC OFF
11
En