Pioneer DDJ-S1 Bedienungsanleitung Seite 33

Problem
No sound is produced.
No sound is produced, or sound is
distorted or noisy.
The beat grid is not displayed.
[SYNC] function does not work.
[SYNC] function does not work even
when files are analyzed.
Fader starting is not possible.
Sound is interrupted when the ASIO
driver is set.
Back cue function does not work.
Reloop function does not work.
Indicator flashes and power does not
turn on.
Library cannot be edited.
ITCH operation is unstable.
Check
Are the connection cables properly connected?
Is the included USB cable properly connected?
Are terminals or plugs dirty?
Is the driver software properly set?
Is ITCH properly set?
Are the connected components and amplifiers
properly set?
Are you operating on USB bus power?
Is the [MIC/AUX THRU] selector switch set to
[ON]?
Is this unit placed near a TV?
Has the music file been analyzed?
Have the music files been properly imported?
Has the music file been analyzed?
Is the beat grid irregular?
Is the beat grid properly tapped?
Are the BPMs of the tracks in the two decks too
different?
Are you scratching?
Are you in standby with a cue set?
Has the ASIO driver been set with ITCH running?
Is a temporary cue point set?
Has a loop been set in the current playback?
—
Is [Protect Library] in [SETUP] enabled?
Are you using the latest version of the software?
Are you using softwares other than ITCH at the
same time?
The computer's USB power supply capacity may
be insufficient.
When other USB devices are connected to the
computer.
Are you using a USB hub?
There is a problem with the USB port to which this
unit is connected.
Is this unit connected to a notebook computer
running on its battery?
The USB buffer size is too small.
Remedy
Connect the connection cables properly. (page 10)
Connect the computer and this unit directly using the included USB cable. USB
hubs cannot be used. (page 10)
Wipe any dirt off terminals and plugs before connecting.
Set the driver software properly. (page 7)
Set ITCH properly.
Check the [Mixer] setting in the [SETUP]. (page 31)
Set the external input selection and volume on the components and amplifiers
properly.
When operating on USB bus power, the [MASTER OUT 1] volume decreases,
the sound quality decreases, sound may not be output, etc.
To use the unit without these limitations, connect the included AC adapter.
(page 10)
Set the [MIC/AUX THRU] selector switch to [OFF]. If the [MIC/AUX THRU]
selector switch is set to [ON], only the sound of the microphone or external
device is output. (page 29)
Turn the TV's power off or install this unit and TV away from each other.
Analyze the file.
If music files cannot be analyzed automatically, click [GRID EDIT] in the ITCH
software and input the beat grids manually.
Reimport the music files and load them in the decks. (page 17)
Analyze the file.
Set the beat grid properly.
The [SYNC] function will not work properly if the BPM of the track on the deck
for which the [SYNC (SYNC OFF)] button is pressed is outside the adjustable
tempo range of the track on the deck for which the [SYNC (SYNC OFF)] button
is not pressed.
The [SYNC] function is disabled when scratching.
Set the cue. (page 23)
Set the ASIO driver before launching ITCH. (page 7)
Set a temporary cue point. (page 23)
If no loop has been set in the current playback, the reloop function does not
work. Set a loop once. (page 23)
Normal operation can sometimes be restored by unplugging the power cord,
waiting at least 1 minute, then plugging the power cord back in.
If the symptom persists, unplug the power cord and request repairs.
Disable [Protect Library]. (page 31)
Free updates of ITCH can be downloaded from the Internet. Check the website
below and keep the software updated to the latest version. (page 6)
Quit other applications to decrease the load on the computer.
If operation continues to be unstable, try disabling the wireless network or other
wireless connections, antivirus software, the screen saver, the low power mode,
etc. (page 6)
Use the included AC adapter. (page 10)
Disconnect other USB devices from the computer.
When another USB audio device is connected to the computer at the same time,
it may not operate or be recognized normally. (page 10)
USB hubs cannot be used. Connect the computer and this unit directly using
the included USB cable. (page 10)
If your computer has multiple USB ports, try connecting this unit to a different
USB port. (page 10)
Supply power to the notebook computer from an AC power supply.
(Depending on the notebook computer's settings, the low power mode may be
set when the computer is running on its battery, automatically reducing the
performance of the computer itself.) (page 6)
Raise the USB buffer size. (page 30)
33
En