dB Technologies DVA S30N Bedienungsanleitung Seite 6

"SUB Phase/Delay" section
11) "PHASE " SWITCH
This switch permits 180° rotation of the audio signal reproduced by subwoofer.
Rotation makes for easier optimization of low-frequency reproduction even in the
most difficult installation situations. After completing installation, reproduce a track of
music and adjust the switch to obtain the best low-frequency sound.
This function it is used also for cardioid configuration.
12) "DELAY" CONTROL
This control allows to delay the sound signal reproduced by the subwoofer.
circuit allows sound-alignment between line array and sub by balancing the various
positions.
This control can also be used to create cardioid configuration systems. The cardioid
configuration provides a remarkable attenuation of the low frequencies radiated by
the rear side of the subs, without changing the direct radiated signal on the front side.
This configuration needs at least 3 subwoofers (two with front radiation and one with
rear radiation).
"RDNET " section
13) INPUT CONNECTOR "DATA INPUT"
RJ45 connector 'data input.
14) OUTPUT CONNECTOR "DATA INPUT"
RJ45 connector 'data output for cascading connections.
15) "LINK" INDICATION LIGHT
This green indicator turns on only when the amplifier has recognized and is
connected with the main RDNET unit via the computer.
16) "ACTIVE" INDICATOR LIGHT
This yellow indicator flashes when there is an active data transmission between
RDNET and the amplifier module.
"DSP UP-grade " section
17) "Service Data USB" Connector
Via this USB connector, it is possible to update the firmware of the DVA S30n
amplifier module using the computer and a dedicated program.
18) "MAINS INPUT" POWER SOCKET
For connecting the power cable.
The connector used for mains connection is a POWER CON® (blue)
19) COOLING GRILLE
These grilles permit cooling the amplifier during operation.
Do not block accesses and clean the grilles whenever necessary to ensure correct
air circulation.
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in
E5 Electromagnetic environment.
9
CHARACTERISTICS AND PROTECTION
Front Grille
The speakers's components in the box are protected by 1.5mm metal steel grille covered by
foam on backside.
Cooling
Thermal control is managed by the main microprocessor that interacts with the local
microprocessors (amplifiers and power supply) and communicates the data to the DSP for
any corrections.
If the amplifier module heats up excessively, the volume is gradually reduced step wise to
This
0.1dB until the module is thermally stabilised.
The volume is automatically restored when the normal operating temperature is reached.
Failure indications and safeties
The microprocessor is able to signal three different kinds of failure by flashing the "READY",
"MUTE /PROT " e "LIMIT"
The three types of failure are:
1) WARNING: a non severe error or auto-ripristinate malfunction is detected and the
performance of the speaker is not limited
2) LIMITATION: an error is detected and diffuser performance is limited. The sound
level is reduced or one or more amplifiers are disabled.
This state partially influences the correct functioning of the diffuser.
If the problem persists the next time the module is turned on, contact the support
centre for assistance.
3) FAILURE: a severe malfunction is detected. The speaker switches to "mute".
If the case of a malfunction, before contacting the support centre, try to turn the module
off and on to check if the problem still exists.
Connecting to the mains supply
Each active speaker features its own power cable. Connection is done by a Neutrik
POWER CON® (blue) model which permits easy and fast connection to the speaker as
well as being an excellent locking system.
The same connector serves as a switch to turn ON and OFF the active loudspeaker by
turning the connector to the left (OFF) or right (ON).
The active speaker must be connected to a power supply able to deliver the maximum
required power.
LOUDSPEAKER INSTALLATION
WARNING
! !
Make sure that the loudspeaker is securely installed in a stable position to avoid any
injuries or damages to persons or property.
For safety reasons do not place one loudspeaker on top of another without proper
fastening systems.
If you use the loudspeakers outdoors avoid places that are exposed to bad weather.
The loudspeaker is supplied by the manufacturer company for use in support.
WARNING
! !
Never use the handle to hang the speaker!
10