Werbung
Characteristics
The record player is equipped with an extremely strong driving motor which reaches a starting torque of 1.8
kg cm. This strong starting torque makes sure that the record player reaches a speed of 33 1/3 rpm in just
0.5 sec. The record player is furthermore equipped with a motor break which ensures a rapid standstill of
the turntable
Unpacking, setting up, assembling
Do not put the mains plug into the mains socket und do not switch the system on before all installations and
adjustments have been carried out.
Take out the record player with its accessories and installation parts, they are partly located in the side of
the Styrofoam protection corners of the packaging.
Remove the shaped pieces of the transport packaging from the system. Keep them for future transporta-
tion.
Place the record player onto an even, stable, vibration-resistant surface. Make sure that the system is not
exposed to direct sun irradiation, there is a risk that the records put on can warp due to the heat.
The record player should not be placed on a shelf together with the speakers, directly on the speakers or on
the floor, but at a distance as far away as possible from the speakers. It is recommended to place it onto a
stable, even surface which is fixed to the wall.
The feet of the record player can be adjusted in height, to make set up more easy.
Carefully place the turntable onto the turntable shaft. Make sure that the two guide mandrils click into the
corresponding jacks. Place the turntable slip mat onto the turntable. With twisting movement slide the pick-
up arm counterbalance onto the rear part of the pick-up arm. The scale of the weight needs to point for-
ward, towards the system carrier. The instructions for the precise setting can be found in chapter Setting of
Pick-up arm
Pick-up arm
Installing the magnet system into the system carrier
Make sure that the stylus protection is on the cartridge during all installations. Connect the contacts of the
system carrier and of the cartridge with the set of cables. On the back of the system there are either colour
codes or a marking is punched in.
white
(L+)
left channel +
blue
(L-)
left channel –
red
(R+)
right channel +
green
(R-)
right channel –
Fix the cartridge with the enclosed screws to the system carrier. Before tightening the screws, slide the car-
tridge approximately into the middle of the oblong holes of the system carrier.
16
Counterbalance
Disposal
In the case that the product no longer works and repair is no longer possible either, please observe the gen-
erally applying legal regulations when disposing of the device
Maintenance and Care
Check the stylus regularly for dust, it needs to be free of all dust. If necessary clean the stylus with a soft
brush and with a little alcohol (never with the finger). Only brush from the back towards the front. Do not use
solvents, these might harm the glue of the stylus, but only clear alcohol or a special stylus cleaner.
Clean the exterior of the system only with a soft, dry cloth or brush. Never use aggressive cleansing agents
or chemical solutions since this might damage the product.
Check the technical safety of the device regularly e.g., for damages on the system unit's cover, the mains
power cord, etc. If there is reason to believe that safe operation has become impossible put the device out
of operation and secure it against any unintended operation.
Safe operation must be presumed to be no longer possible, if
• the device exhibits visible damage
• the device does not operate any longer
• the device was stored under unfavourable conditions for a long period of time.
or
• the device was exposed to extraordinary stress caused by transport.
Before cleaning or servicing the device, please observe the following safety instructions.
Troubleshooting
With this device you have bought a state of the art product. However, problems or disturbances can arise.
This why we would like to inform you can, how you can put an end to possible disturbances:
Malfunction:
Possible cause:
No drive, no speed display
Mains connection interrupted,
Power switch not switched on
Sound reproduction too low or to high
Wrong speed setting
Distorted sound reproduction
Wrong stylus force setting
Amplifier/mixing desk in overdrive
The phono input was not used to connect to the
amplifier/mixing desk
Cartridge defect or worn
Pick-up arm can not be lowered
Wrong setting of stylus force
Interfering noises
Record or cartridge stylus dirty
Wrong setting of stylus force
Connection to earth cable faulty
No playback on both channels
Volume on amplifier/mixing desk set to minimum
Connection of cinch cable faulty
Playback only via one channel
Balance adjuster on amplifier/mixing desk set wrong
Connection of cinch cable faulty
21
Werbung
Kapitel
