MONTAGE- und BETRIEBSANLEITUNG
FEUCHTE / TEMPERATUR MESSUMFORMER
Type: SERIE EE04
ALLGEMEIN:
Messumformer der Serie EE04 sind für die Erfassung von Feuchte und Temperatur bestimmt.
Als Feuchtesensor wird ein hochgenauer, kapazitiver Sensor der Serie HC 103 von E+E ver-
wendet.
Anwendung findet die Serie EE04 beispielsweise in Be- und Entfeuchtungsanlagen,
Trocknungsprozessen (z.B. Wäschetrockner), bei der Überwachung von Lagerräumen & feuch-
teempfindlichen Geräten (z.B.: Fotokopiermaschinen, Kühlschränken usw.) und auch bei
Fahrzeugklimaanlagen.
Bei Sonderanwendungen wenden Sie sich bitte an den Hersteller oder an Ihren zuständigen
Händler.
ACHTUNG:
Extreme mechanische und unsachgemäße Beanspruchungen sind unbedingt zu vermeiden.
Bei Wartungsarbeiten sind ESD Schutzmaßnahmen erforderlich.
REINIGUNGSHINWEISE:
- Filter keinem Druckwasser aussetzen
- Filter nur mit weicher Bürste reinigen
TECHNISCHE DATEN:
FEUCHTE
Arbeitsbereich
0...95%r.F.
Feuchtesensor
HC103
Genauigkeit bei 25°C
± 3 %r.F. (40...60 %r.F.) ± 5 %r.F. (0...95%r.F.)
Feuchteausgang
linearer Analogausgang
z.B.:bei U
R
> 5kOhm
Last
TEMPERATUR
Temperaturausgang
Spannungsteiler:
Betriebstemperatur
-40...85°C
ALLGEMEIN
Versorgungsspannung (U
)
5VDC ±10%
V
Stromaufnahme
typ. 1,4mA ohne Last am Ausgang
< 3,5mA mit maximaler Last amAusgang
Ansprechzeit
Schutzklasse
Sensorseite: IP64 (mit Teflon-Filter)
Elektromagnetische Verträglichkeit
EN 50081-1
Achtung! Modul ist nicht gegen Stossspannungen (SURGE) geschützt!
BA_EE04_03 // Technische Änderungen vorbehalten // 302228
mit Coating 0...100%
0...100%r.F.
= 0,1 x U
bis 0,9 x U
V
= 5VDC:
0...100%r.F. = 0,5V...4,5VDC
V
30%r.F. = 1,7V
NTC (10kOhm bei 25°C) mit
Pull down-Widerstand (10kOhm)
bei 25°C < 45s
63
Steckerseite: IP30
IP20 (ohne Teflon-Filter)
EN 61000-6-2
GENERAL:
Transmitters of the EE04 series are designed to measure humidity and temperature. The humi-
dity sensor element is a capacitive sensor of the HC103 series from E+E.
Common applications for the EE04 transmitter are e.g. in the field of humidifiers and dehumidi-
fiers, dryers, monitoring of storage rooms & humidity sensitve devices (e.g.: photocopiers, refri-
gerators...) and also air conditioners for cars.
For special purpose applications please contact the manufacturer or your distributor.
ATTENTION:
Absolutely avoid extreme mechanical and improper strain.
For maintenance purposes it is recommended, to observe the valid ESD-safety precautions!
CLEANING NOTES:
- Do not clean filter with pressure water
- Clean filter with a soft brush only
TECHNICAL DATA:
HUMIDITY
working range
humidity sensor element
accuracy at 25 degC
humidity output
V
R
Load
TEMPERATURE
temperature output
operating temperature
GENERAL
supply voltage (U
)
supply
supply current
response time
protection class
Electromagnetic compatibility
Attention! The module has no protection against surge voltages!
OM_EE04_02 // technical data are subject to change
INSTRUCTIONS for SETTING UP and OPERATING
HUMIDITY / TEMPERATURE TRANSMITTER
Type: SERIES EE04
0...95%RH
with coating 0...100%RH
HC103
± 3 %RH (40...60%RH) ± 5 %RH (0...95%RH)
linear analogue output
0...100%RH
= 0.1 x U
supply
e.g.: at U
= 5VDC:
0...100%RH = 0.5V...4.5VDC
supply
30&%RH = 1.7V
>5kOhm
voltage divider:
NTC (10 kOhm at 25degC) and
pull down-resistor (10kOhm)
-40...85degC
5VDC ±10%
typ. 1.4mA without load at output
< 3.5mA with maximum load at output
at 25°C < 45s
63
sensor side: IP64 (with teflon-filter) connector side: IP30
IP20 (without teflon-filter)
EN 50081-1
EN 61000-6-2
to 0.9 x U
supply