Inhaltsverzeichnis
Werbung
REF. NR.
DESCRIPTION
26
SPRING
67
GEAR WHEEL
32
POSITIONING RING
30
CLAMP RING
88
ROTOR-ASSEMBLEY
84
STATOR ASSEMBLY
82
CARBON BRUSH WITH SPRING
80
BRUSH HOLDER
98
CAPACITOR
97
SWITCH
26
SPARE PARTS LIST
TOLEDO NR.
English
UK
407630
Cutting-off machine
407631
407632
TECHNICAL SPECIFICATIONS
407633
Voltage
407634
Frequency
407635
Power input
No-load speed
407636
Disc diameter
Max. cutting depth 90°
407637
Max. cutting depth 45°
407638
Weight
Lpa (sound pressure)
407639
Lwa (sound power level)
Vibration value
PACKAGE CONTENTS
1 Cutting-off machine
1 Saw blade
1 Instruction manual
1 Safety instructions
1 Guarantee card
Check the machine, loose parts and accessories for
transport damage.
DESCRIPTION (PAGE 2)
1. Grip with switch
2. Unlocking button
3. Motor housing + cover
graphite brushes
4. Saw blade attachment
5. Moveable safety guard
SAFETY INSTRUCTIONS
The following symbols are used throughout this manual:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and per-
sonal injury.
Read the following safety instructions. Keep
these instructions in a safe place.
Toledo
Toledo
Electrical safety
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and per-
sonal injury. Read the following safety instruc-
tions and also the enclosed safety instructions.
Keep these instructions in a safe place!
Always check that the power supply corresponds to
the voltage on the rating plate.
| 230 V~
The machine is double insulated in accordance
| 50 Hz
with EN50144; therefore no earth wire is
| 800 W
required.
| 4500/min
| 205 x 18 mm
Replacing cables or plugs
| 120x50 mm
Immediately throw away old cables or plugs when they
| 70x55 mm
have been replaced by new ones. It is dangerous to insert
| 7.0 kg
the plug of a loose cable in the wall outlet.
| 88.9 dB(A)
| 101.9 dB(A)
Using extension cables
| 2.5 m/s
2
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
the reel completely.
SPECIAL SAFETY INSTRUCTIONS
BEFORE EACH USE
-
Check the cutting-off machine. If any part of the cut-
ting-off machine is missing, bent or unusable in anot-
her way, or if electrical faults occur, switch off the
machine and remove the plug from the socket.
Replace all missing, damaged or faulty parts, before
using the machine again.
6. Table adjustment screws
-
Make sure that hands, eyes, face and ears are well
7. Rotary table
protected.
8. Degree scale
-
Use of safety goggles without the CE quality mark can
9. Fastening holes
lead to serious injury if the glass breaks.
10. Bevel adjustment bolt
-
In order to prevent the saw blade from becoming
11. Protective cover
jammed in the saw cut and workpieces being flung
away, the instructions below must be followed:
-
Choose a suitable saw blade for the work.
Only use the cutting-off machine to saw wood
and derived products, or light metals such as alu-
minium. Other materials can be flung away, get
caught in the saw blade or cause other dangers.
-
The arrow on the saw blade, which indicates the
direction of rotation, must point in the same
direction as the arrow placed on the machine.
The saw blade teeth must point downwards on
the front of the saw.
-
Check whether the saw blade is sharp, undama-
ged and well aligned. Press the saw head down-
wards after removing the plug.
Turn the saw blade by hand and see whether it
turns freely. Put the machine in the 45 position
and repeat the test. If the saw blade touches any-
where, it must be adjusted again.
-
Keep the saw blade and the tensioning surfaces of
the clamps clean.
-
The saw blade flange must always be mounted
with the tightened recess towards the saw blade.
. When using a cable reel always unwind
2
3
Werbung
Inhaltsverzeichnis
