Eingang Ethernet ShowMe- 10/100Mbit Taster 3. Lieferumfang • 1 x Kindermann QuickSelect 3.0+ • 1 x Netzteil 100-240 V~ / 12 V DC, 3 A, mit verschraubbarem Kleinspannungsanschluss • 2 x Haltewinkel für Montage des Gehäuses • 4 x Gerätefüße •...
4. Systembeschreibung Das QuickSelect 3.0 + ist ein Multiformat Umschalter für die Übertragung von analogen und digitalen AV-Signalen über ein HDBT-Bussystem in Reihenschaltung (Daisy Chain) oder Ringschaltung. Das QuickSelect 3.0 + ist Sender und Empfänger zugleich. Das Gerät besitzt Signal-Eingänge für: 2 x HDMI, 1 x VGA plus analogem Stereo-Audio, 1x HDBT-In sowie einen Ethernet-Anschluss.
Funktionen • Eingangsselektion wahlweise über Kontakteingänge, ShowMe-Taster, RS232 oder per integrierter automatischer Signalerkennung • Umsetzung des Eingangssignals auf HDBT um auf Cat-6/7 (AWG23) über eine große Entfernung zu senden (Bild und Ton unidirektional, RS232 und LAN bidirektional) • Die Reichweite beträgt bei 1080p bis zu 100 m, 4K60 bis zu 30 m •...
Seite 6
Anwendungsbeispiel: Reihenschaltung Projektor Projektor HDMI Laut- Audio sprecher RS232 Cat-Kabel (HDBT) Medien- steuerung R S 2 3 A u d i Display Display L i n k L i n k L i n k o u t o u t o u t H D M H D M...
5.2 Geräte-Adressen manuell konfigurieren Mit Hilfe eines kleinen Schlitz-Schraubendrehers die beiden BCD-Drehschalter an der Rückseite jedes QuickSelect Gerätes auf eine individuelle Adresse zwischen 01…98 einstellen. Die Adresse 00 ist für den speziellen Fall einer Ringverkabelung reserviert und muss in diesem Fall zwingend dem „ersten“...
6. Konfiguration über die grafische Benutzeroberfläche (GUI) Die kostenlose Konfigurations-Software zum Download finden Sie in unserem Händlerportal (nur für Wiederverkäufer): http://shop.kindermann.de/erp/webshop/navigationPath/7447000500.html Bitte stellen sie eine Verbindung zwischen Ihrem PC und dem QuickSelect 3.0 + System per RS232 her (Pinbelegung für GUI auf S. 19). Falls Ihr PC keinen RS232-Anschluss haben sollte, bedienen Sie sich bitte eines RS232/USB Adapters.
6.2 Experten Ansicht Durch Auswählen des Modus ‚Expert‘ wechselt die Software in die Experten Ansicht. Hier können Sie Ihr Quickselect System individuell konfigurieren. Dies ist z. B. nötig, um unterschiedliche EDIDs in den einzelnen Transmittern zu hinterlegen, ON/OFF Befehle zu nutzen oder die HDMI-Ausgänge zu konfigu- rieren.
Systemübersicht und Adressvergabe: Mit dem Betätigen dieser Taste werden die in dieser Kette verbundenen und korrekt angeschlossenen, QuickSelect 3.0+ Transmitter gesucht und er- kannt. Die linke der beiden Zahlen stellt die interne ID dar (für den Benutzer nicht relevant) und die zweite Zahl die momentan vergebene Adresse. Mit Auto Address werden die Adressen automatisch vergeben (gilt nur für die Geräte, deren BCD Schalter auf 99 stehen).
Seite 11
Das QuickSelect 3.0 + System leitet die EDID Tabelle des Endgerätes nicht automatisch an die Bildquelle weiter. Unter bestimmten Umständen wäre dies auch unerwünscht, da z. B. DVI Endgeräte keine Toninformationen enthalten – somit der Laptop über HDMI auch keinen Ton ausgeben würde. Darum ist ein EDID Management im GUI des QuickSelect 3.0 + vorgesehen.
- Valens Chipset Ausgang Um eine neuere Firmware auf ein QuickSelect 3.0+ zu laden gehen Sie bitte wie folgt vor: Kopieren Sie den über Kindermann zur Verfügung gestellten Firmware File auf einen USB Stick ins Hauptverzeichnis (Dateiname: MERGE.BIN). 2. Trennen Sie das zu fl ashende QuickSelect 3.0+ von der Stromversorgung und stecken Sie den USB Stick in dessen USB Ladebuchse.
Display bidirektional übertragen (pass through). Schließen Sie z. B. die RS232-Schnittstelle der Mediensteuerung einfach an eine RS232-Klemme an. Das ausführliche RS232-Protokoll und einen Treiber für Neets-Steuerungen fi nden Sie online unter: shop.kindermann.de/evp/webshop/navigation_Path/7447000500.html RS232 Befehle manuell eingeben und Antworten auslesen: Über diese Textfelder können Sie RS232 Befehle senden und die Antwort der QuickSelect 3.0+ Kette auslesen.
Seite 16
Display Power Control Funktion: Mittels der Display Power Control Funktion ist das direkte, automatische Ein- und Ausschalten eines oder mehrerer Displays oder Projektoren bei Signalerkennung auch ohne externe Steuerung möglich. Hierzu muss jedes der Wiedergabegeräte mit jeweils einem Quickselect Modul per RS232 verbunden werden. Ist das letzte Quickselect einer Kette über den HDBT Link-out mit einem kompatiblen Anzeigegerät verbun- den so können zusätzlich zum Bildsignal auch die RS232 Befehle über diese Verbindung an das Anzeige- gerät übertragen werden (vorbehaltlich der Kompatibilität des zu steuernden Gerätes).
8. Bedienung per ShowMe-Taster Sind die Quickselect-Geräte für die Teilnehmer frei zugänglich aufgestellt (z. B. auf einem Tisch), so kann die Aktivierung entweder durch Drücken der frontseitigen ShowMe Taste erfolgen oder auch automatisch durch Signalerkennung (hierzu „Auto ShowMe“-Betrieb mittels Konfi gurationssoftware einschalten). Für den Fall eines verdeckten Einbaus verfügt jedes QuickSelect an der Rückseite über Anschlüsse für drei externe Taster mit Status-LED, damit der Anwender jeden Eingang auch separat, z.
11.2 Zwei Tische oder Bodentanks mit HDBT-fähigem Projektor 11.2 Zwei Tische oder Bodentanks mit HDBT-fähigem Projektor 11.2 Zwei Tische oder Bodentanks mit HDBT-fähigem Projektor 2 x HDMI, VGA 2 x HDMI, VGA Control + LED Control + LED Link Out Link In Link In Link Out...
Table of contents Safety instructions Connections front and rear Scope of delivery System description and functions Quick system setup 5.1. Wiring devices 5.2. Manual device address awarding 5.3. Automatic device address awarding (address “99“) 5.4. Reading and saving EDID information of playback devices 5.5. Chain or Ring-Setup? Configuration with the graphical user interface 6.1. Basic configuration 6.2. Expert configuration RS232 control Operation by ShowMe button Technical data 10. Available accessories 11. Application examples 11.1. Single-table solution with HDBT-wall connection panel 11.2. Two tables or flood tanks with HDBT-capable projector 11.3. Conference table with WiPG and operating options in every position 1. Safety instructions • Please read the instructions with care and keep them •...
10/100Mbit button 3. Scope of delivery • 1 x Kindermann QuickSelect 3.0+ • 1 x mains unit 100-240 V~ / 12 V DC, 3 A, with screwable extra-low voltage connection • 2 x mounting bracket for under-desk mounting of the device •...
Seite 23
The signal inputs at the device can either be activated directly via the ShowMe button or via external buttons (connected to Phoenix terminals at the rear). If an active source is connected in automatic mode, this input is directly activated by an automatic signal recognition. Those outputs can be switched to different signal inputs (one locally and one HDBT-In).
5. Quick system setup A quick setup of a Quickselect chain is done in 3 easy steps: 1. Wiring devices 2. Device address awarding (manual or automatic) 3. Reading and saving EDID information of playback devices Standard settings can be confi gured quick and easy using the following setup assistant procedures. Specifi c individual settings can be made with a laptop using the free confi guration software via the RS232 connection.
5.1 Wiring devices Connect all mains units to the devices, only tightening the cap nut manually. Do not connect the mains units to the mains outlet. Connect deactivated QuickSelects with a cat-6 cable (AWG 23), connect link output of the first device to the link input of the next QuickSelect 3.0, proceed accordingly until all devices are connected in series.
6. Configuration via the graphical user interface (GUI) The free configuration software for download can be found on our dealer portal (for resellers only): http://shop.kindermann.de/erp/webshop/navigationPath/7447000500.html Please connect your PC to the QuickSelect 3.0+ System by RS232 (for pin assignment for GUI, see p. 35).
Seite 27
6.2 Expert view Selecting the „Expert“ mode will cause the software to switch to expert view. You can individually confi gure your Quickselect system here. This is necessary, e.g. to fi le diff erent EDIDs in the individual transmitters, use to power control via RS232 or to confi gure the HDMI outputs. Field to display the device chain (devices appear after Output of the EDID information.
Seite 28
Note: By using the external contact switches for source-switching only the signal on the HDBT-Out can be selected. Local HDMI-Out and Audio-Out will follow those commands only if „Link In/Link Out“ is selected. The default setting is“Link In/Link out”. In this case any signal coming via Link In from the proceeding unit as well as signals infed locally will be available on both outputs, HDMI and Link Out, at the same time.
Seite 29
3. In EDID mode ‚User‘, you can load customized EDID tables and write to the respective HDMI inputs: In the upper pulldown menu, you can read out the respective EDID table of the connected output device or the tables filed in the inputs Note: This in turn can be saved locally as a file.
Seite 30
VGA to HDMI converter: The integrated VGA to HDMI Scaler converts analogue video and audio signals into an HDMI signal. To achieve the highest possible quality from the VGA source signal, the resolution of the video signal fed-in via VGA can be adjusted on the output side.
Seite 31
- Valens chip set output To load a newer fi rmware onto a QuickSelect 3.0+, proceed as follows: Copy the fi rmware fi le provided by Kindermann to the root directory of an USB stick (Filename: MERGE.BIN). 2. Disconnect the QuickSelect 3.0+ to be fl ashed from the power supply and connect the USB stick to its USB charge socket.
RS232-terminal. The detailed RS232-protocol and a driver for Neets controls can be found online at: shop.kindermann.de/evp/webshop/navigation_Path/7447000500.html Enter RS232 commands manually and read out answers: You can use these text fi elds to send RS232 commands and read the response of the QuickSelect 3.0+ chain.
In order to defi ne the parameters, fi rst insert the commands for ‚Power On‘ and for ‚Power Off ‘ into the corresponding command lines, either using hexadecimal format or ASCII format. Next, specify if the “end of line” code must be sent or not (Send CR / No CR, CR=Carriage Return). Using the ‚Timer/s‘ fi elds an individual timeout between 0-9999 seconds can be assigned to both, the power-on and power-off commands.
Screensaver: If a Quickselect unit is activated without any active source being connected (by pressing the internal or external Show-Me button), the screensaver of the internal VGA-to-HDMI scaler appears. The screensaver shows the current installed firmware version of the individual Quickselect module. If required in specific cases the screensaver can be deactivated (or re-activated) by using the RS232 “Send”...
Supports Extended Display Identifi cation Data (EDID) and Display Data Channel EDID/DDC (DDC) data via DVI and HDMI Standards, EDID and DDC signals HDCP Compatible with high-bandwidth Digital Content Protection (HDCP 2.0). 100 VAC ~ 240 VAC, 50/60 Hz Energy 12 W max.