Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6 - NICKEL DISCHARGING
1. Connect the battery connector to the device connector.
9. Press the arrow in the top right of the LCD Touch Screen to see the rest of
the Discharging information.
2. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.
NiMH DCHG
Program select=NiMH
End Volt
:
Int Temp
:
Safety Timer
:
Capacity Limit :
N i M H
STOP
CHG
DCHG
CYCLE
10. Press Graph to see the battery voltage graph. Press Back to return to the
3. Press DCHG.
discharging screen.
NiMH DISCHARGE
End Volt
:
0.10V
Data NiMH = Graph
Capacity
:
50mAh
Current
:
0.1A
Press&Hold
:
DISCHRG
BACK
SELECT
8.39V
000:47S
4. Press a parameter to highlight that parameter.
11. Press STOP at any time to stop discharging.
5. Press the Up and Down Arrows to edit the parameter.
12. When discharging is complete, the charger will sound a series of beeps and
6. Press Select to save the parameter.
display the following screen:
7. Once the parameters are at the desired settings, press and hold DISCHRG.
NiMH DONE
8. The charger will check the battery and charger settings and discharging will begin. The
Capacity
:
charger will beep and display the following screen:
Current
:
Voltage
:
Resistance
:
NiMH DCHG
000:34S
Peak Temp.
:
Capacity
:
16mAh
BACK
Cycle
Current
:
1.8A
Voltage
:
8.43V
Resistance
:
****mΩ
13. Press the arrow in the top right of the LCD Touch Screen to see the rest of
Peak Temp.
:
No sens
the Charging information.
STOP
Graph
NiMH DONE
End Volt
:
Int Temp
:
Safety Timer
:
Capacity Limit :
STOP
14. Disconnect the battery from the charger.
7 - NICKEL CYCLE CHARGING
1.
Connect the battery connector to the device connector.
11. Press CYCLE to see the voltage and amperage applied to each cycle.
2.
Press the Left and Right Arrows on the LCD Touch Screen to scroll
Data NiMH = Cycle 1/1
through the main menu screens until you reach Program Select=Ni-MH/
Ni-Cd.
--CHG--
00.00Vp
Program select=NiMH
00000mAh
Back
UP
N i M H
12. Press Graph to see the battery voltage graph. Press Back to return to the
charging screen.
CHG
DCHG
CYCLE
Data NiMH = Graph
3. Press CYCLE.
NiMH CYCLE
[1/2]
Capacity
:
3300mAh
CHG Curr.
:
3.3A
DCHG Curr.
:
0.1A
DCHG End Volt
:
0.10V
8.03V
000:28S
Press&Hold
:
CYCLE
13. Press STOP at any time to stop charging.
BACK
SELECT
14. When cycle charging is complete, the charger will sound a series of beeps and
4. Press a parameter to highlight that parameter.
display the following screen:
5. Press the Up and Down Arrows to edit the parameter.
NiMH DONE
6. Press Select to save the parameter.
Capacity
:
7. Press the top right of the LCD Touch Screen to get to the next set of
Current
:
Voltage
:
parameters.
Resistance
:
8. Once the parameters are at the desired settings, press and hold CYCLE.
Peak Temp.
:
9. The charger will check the battery and charger settings and cycle charging will
BACK
Cycle
begin. The charger will beep and display the following screen:
NiMH CYCLE
000:06S
15. Press the arrow in the top right of the LCD Touch Screen to see the rest of
Capacity
:
4mAh
the Charging information.
Current
:
3.3A
Voltage
:
7.97V
Resistance
:
53mΩ
Peak Temp.
:
No sens
NiMH DONE
STOP
CYCLE
Graph
Input Volt
:
Delta Peak
:
Int Temp.
:
10. Press the arrow in the top right of the LCD Touch Screen to see the rest of
Safety Timer
:
the Cycle information.
Capacity Lim. :
NiMH DONE
001:15S
BACK
Cycle
Input Volt
:
14.8?V
Delta Peak
:
8mV/C
Int Temp.
:
60F
16. Disconnect the battery from the charger.
Safety Timer
:
240min
Capacity Lim. :
3300mAh
BACK
Cycle
Graph
CAUTION: The Pb charge program menus are to be used ONLY for the charging and discharging of Pb battery packs. Charging other battery types using the Pb
charge programs will damage the battery or the charger.
8 - PB CHARGING
1. Connect the battery connector to the battery adapter cable.
9. Press START. The charger will beep and display the following screen:
2. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
Pb CHG
the main menu screens until you reach Program Select=Pb.
Capacity
:
Current
:
Program select=Pb
Voltage
:
Resistance
:
Peak Temp.
:
STOP
CHG
DCHG
10. Press the arrow in the top right of the LCD Touch Screen to see the rest of
the charging info.
3. Press CHG.
11. Press Graph to see the battery voltage graph. Press Back to return to the
charging screen.
Pb CHARGE
Pack. Volt.
:
2V/1P
Data Pb
= Graph
Capacity
:
50mAh
Current
:
0.1A
Press&Hold
:
CHARGE
BACK
SELECT
14.68V
000:12S
4. Press a parameter to highlight that parameter.
12. Press STOP at any time to stop charging.
5. Press the Up and Down Arrows to edit the parameter.
13. When charging is complete, the charger will sound a series of beeps and
6. Press Select to save the parameter.
display the following screen:
7. Once the parameters are at the desired settings, press and hold CHARGE.
8. The charger will check the battery and charger settings and display the
Pb DONE
Capacity
:
following screen:
Current
:
Pb Charge Confirm
Voltage
:
Resistance
:
Peak Temp.
:
-Connect-
-Check-
BACK
Input • • • • OK
Set: 6P
BATT. • • • • OK
Read: 5P
14. Disconnect the battery from the charger.
Back
START
9 - PB DISCHARGING
1.
Connect the battery connector to the battery adapter cable.
9. Press START. The charger will beep and display the following screen:
2.
Press the Left and Right Arrows on the LCD Touch Screen to scroll
through the main menu screens until you reach Program Select=Pb.
Program select=Pb
000:09S
12.24V
21ºC
240min
2100mAh
CHG
DCHG
10. Press the arrow in the top right of the LCD Touch Screen to see the rest of
Graph
the discharging information.
3. Press DCHG.
11. Press Graph to see the battery voltage graph. Press Back to return to the
Discharging screen.
Pb DISCHARGE
Pack. Volt.
:
2V/1P
Capacity
:
50mAh
Current
:
0.1A
BACK
Press&Hold
:
DISCHRG
BACK
SELECT
4. Press a parameter to highlight that parameter.
12. Press STOP at any time to stop discharging.
5. Press the Up and Down Arrows to edit the parameter.
13. When discharging is complete, the charger will sound a series of beeps and
6. Press Select to save the parameter.
display the following screen:
7. Once the parameters are at the desired settings, press and hold DISCHRG.
8. The charger will check the battery and charger settings and display the
following screen:
001:15S
53mAh
Pb DCHG Confirm
0.0A
8.16V
53mΩ
-Connect-
-Check-
No sens
Input • • • • OK
Set: 6P
BATT. • • • • OK
Read: 5P
Graph
14. Press the arrow in the top right of the LCD Touch Screen to see the rest of
BACK
START
the Charging information.
15. Disconnect the battery from the charger.
000:09S
12.24V
21ºC
240min
2100mAh
Graph
10 - SETUP
1. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
Parameters
the main menu screens until you reach Program Select=Setup.
Program select=Setup
--DISCHG--
00.00Va
Input Power Low Voltage Cutoff 10.0V–17.5V
00000mAh
Down
SETUP
2. Press SETUP.
USER SETUP
[1/4]
BACK
Temp (ºC/ºF)
:
ºC
Temp Cutt-Off :
60ºC
Input Low Volt :
10.0V
Input Limited :
Auto
DCHG Mode
:
CC
BACK
SELECT
3. Press a parameter to highlight that parameter.
4. Press the Up and Down Arrows to edit the parameter.
5. Press Select to save the parameter.
6. Press the top right of the LCD Touch Screen to get to the next set of
001:15S
parameters.
53mAh
0.0A
8.16V
USER SETUP
[2/4]
53mΩ
Balance Volt
:
Auto
No sens
Balance Force :
Auto
Full Force
:
Auto
Graph
MH/Cd Trickle :
OFF
Safety Timer
:
240min
BACK
SELECT
USER SETUP
[3/4]
Back Light
:
100%
001:15S
Melody
:
1
14.8?V
Button Sound
:
ON
8mV/C
Buzzer Sound
:
ON
60F
Buzzer Vol
:
100%
240min
3300mAh
BACK
SELECT
Graph
USER SETUP
[4/4]
<
ENTER_USER_NAME
>
Version#
:
1.00
Press&Hold
-≥
FCTY_RST
BACK
SELECT
11 - VIEW
1. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
3. Press CELLS to view the connected lithium battery's individual cell voltage.
the main menu screens until you reach Program Select=View.
Program select=View
000:16S
8mAh
1.7A
14.69V
VIEW
BALANCE
****mΩ
No sens
2. Press VIEW. The screen will display the current charger status.
Graph
DATA VIEW
Input Volt
:
15.30V
Output Volt
:
0.02V
Int Temp.
:
29ºC
Ext Temp.
:
No sens
Resistance
:
****mΩ
BACK
CELLS
BACK
12 - BALANCE
1. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
5. Press STOP at any time to stop balancing.
the main menu screens until you reach Program Select=View.
6. When balancing is complete, the charger will beep and display the following
screen:
Program select=View
000:19S
VIEW
BALANCE
8mAh
1.7A
11.60V
2. Press BALANCE.
****mΩ
3. Press the type of battery you want to balance: Li-Po/Li-Ion/Li-Fe.
No sens
4. Press START. The charger will begin balancing the cells.
Graph
BATTERY
LiPo
LiIon
LiFE
BACK
START
13 - MEMORY
1. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
the main menu screens until you reach the battery program you would like to
Pb DCHG
000:19S
save: Program Select=Li-Po/Li-Fe/Li-Ion/Ni-MH/Ni-Cd/Pb.
Capacity
:
8mAh
Current
:
1.7A
2. Press the action at the bottom of the LCD Touch Screen to enter that menu.
Voltage
:
11.60V
3. Press a parameter to highlight that parameter.
Resistance
:
****mΩ
4. Press the Up and Down Arrows to edit the parameter.
Peak Temp.
:
No sens
STOP
Graph
5. Press Select to save the parameter.
6. If there is more than one screen of parameters, press the top right corner of
the LCD Touch Screen to scroll through the parameter screens.
7. Once the parameters are at the desired settings, press Back to return to the
main menu screens.
8. Press the Left and Right Arrows on the LCD Touch Screen to scroll through
Data Pb
= Graph
the main menu screens until you reach Program Select=Memory.
BACK
Program select=Memory
11.54V
000:32S
MEMORY
9. Press MEMORY.
Pb DONE
000:19S
Capacity
:
8mAh
Current
:
1.7A
Voltage
:
11.60V
Resistance
:
****mΩ
Peak Temp.
:
No sens
BACK
Graph
14 - USB DEVICE CHARGING
The charger has the capability to charge any USB-compatible device with the 2.1A USB Power Output Port (F). To use the charging function, simply connect a
compatible charging device or cord into the charge port while the charger is powered ON. The charger provides up to 2.1A current at 5V DC.
15 - TROUBLESHOOTING
During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger's LCD screen, make the recommended
responses. If the message continues after you respond as recommended, contact your Staufenbiel customer service center for assistance.
REVERSE POLARITY
Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery.
PROCESS INTERRUPTED
Make sure the power connections are correct for charging.
OUTPUT SHORT CIRCUIT
Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.
INPUT VOLTAGE ERROR
Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger
provides correct input voltage.
Temperature °C/°F
CHARGER FAILURE
Charger electronics require repair.
Temperature Cutoff 68–176°F (20–80°C)
BATTERY LOW VOLTAGE
Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the
battery.
Input LImited 1.0–16,5A
BATTERY HIGH VOLTAGE
Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the
battery.
DCHG Mode CC–CV
Balance Voltage 0.01V–0.03V
CELL LOW VOLTAGE
Cell voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the
battery.
Balance Force -0.01–7.00V
CELL HIGH VOLTAGE
Cell voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the
MH/Cd Trickle 50mA–200mA
battery.
Safety Timer 1–255 minutes
CELL CONNECT ERROR
Make sure the balance connection is correct for charging.
Back Light OFF–100%
CHARGER OVERHEATING
Charger temperature is too high. Power OFF the charger and let it cool.
Melody 1–5
OVER POWER
Input voltage to the charger exceeded the default or adjusted input voltage setting. Make sure the power source for the charger provides
Button Sound ON/OFF
the correct input voltage.
Buzzer Sound ON/OFF
MAX CURRENT
Current is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
Buzzer Volume 0–100%
SAFETY TIMER
Maximum safe time limit has been reached.
Username Enter your name here
MAX CAPACITY
Maximum capacity limit has been reached.
Version 1.0
MAX EXT. TEMP
External temperature is too high. Let charger and battery cool.
Press and hold FCTY RST to return the
Factory Reset
charger to default factory settings.
DATA View–CELLS
BACK RES.
0.00 0.00 0.00 0.00 0.00 0.00
–Balancing Complete–
BACK RES.
BACK RES.
3.94 3.94
0.00 0.00 0.00 0.00
Warranty and Service Contact Information
10. Choose an empty memory profile and press it.
Contakt
Dymond / Staufenbiel
USER SETUP
[1/4]
M01 NULL
Deutschland / Germany
Gustav Staufenbiel GmbH
M02 NULL
M03 NULL
M04 NULL
Schweiz / Switzerland
Gustav Staufenbiel GmbH
M05 NULL
BACK
DEL
LOAD
SAVE
Frankreich / France
Gustav Staufenbiel GmbH
11. Press SAVE. The charging parameters you just entered will be saved in that
memory profile.
12. To use a memory profile, press it, then press LOAD.
13. To delete a memory profile, press it, then hold DEL.
EU Compliance Statement: Gustav Staufenbiel GmbH hereby declares that this
14. Press the top right of the LCD Touch Screen to scroll through all 20 memory
product is in compliance with the essential requirements and other relevant
profiles.
provisions of the EMC and LVD Directives
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contact Information
Address
+49 (0) 40 300 61 950
Hanskampring 9
info@modellhobby.de
22885 Barsbüttel
+41 (0) 500 64 40
Rathausstrasse 14
info@staufenbiel-shop.ch
CH 6340 Baar
+33 (0) 70 822 63 500
Hanskampring 9
info@modellhobby.fr
22885 Barsbüttel
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user's
responsibility to dispose of their waste equipment by handing it over to a desig-
nated collections point for the recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at the time of disposal will help
to conserve natural resources and ensure that it is recycled in a manner that protects hu-
man health and the environment. For more information about where you can drop off your
waste equipment for recycling, please contact your local city office, your household waste
disposal service or where you purchased the product.
FCC INFORMATION
Werbung
