Intended Use - Conrad 75 41 39 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
Peephole monitor
Item no. 75 41 39

Intended use

The peephole monitor is intended to provide improved recognition of visitors in front of a front door by means
of a small monitor. The camera is integrated on the back of the peephole monitor; the picture is taken through
the enclosed peephole.
As an additional feature, it is also possible to insert a microSD-memory card to store the camera pictures,
so the pictures can be checked later.
Always observe the safety instructions and all other information included in these operating instructions.
This product complies with the applicable National and European requirements. All names of companies and
products are the trademarks of the respective owner. All rights reserved.
Package Contents
1 Peephole monitor
2 Plastic retainer (for attaching the peep-
hole monitor on the peephole)
3 Metal washer
4 Peephole lens
5 Peephole threaded sleeve
6 Installation spanner for attaching the
peephole
7 Two batteries type AA/Mignon for the
peephole monitor
Furthermore:
• Manufacturer's instruction manual in
English and illustrations for the installa-
tion
• Quick guide
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We do not assume liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper use
or non-compliance with the safety instructions. In such cases, the warranty will be null
and void.
• The unauthorised conversion and/or modifi cation of the product is not permitted for safety
and approval reasons (CE). Never take the product apart (except according to the procedure
described in these operating instructions).
• The product is not a toy and must be kept out of the reach of children. It should be operated
out of the reach of children.
• The product should be used only in dry indoor areas; it must not get wet or damp.
• Do not leave packaging material carelessly lying around since it could become a dangerous
plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental drops, even
from a low height.
General information on batteries/rechargeable batteries
• Batteries/rechargeable batteries must be kept out of the reach of children.
• Do not leave batteries/rechargeable batteries lying around; they could be swallowed by children or pets. If
swallowed, consult a doctor immediately.
• Leaking, or damaged batteries/rechargeable batteries, in contact with the skin can cause acid burns,
therefore, use suitable protective gloves.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a fi re. There is a risk of
explosion!
• Do not recharge normal, non-rechargeable batteries, risk of explosion! Only charge rechargeable batteries
that are intended for this purpose; use a suitable battery charger.
• Never mix standard batteries with rechargeable batteries, use either standard batteries or rechargeable
batteries.
• Do not mix batteries/rechargeable batteries with different charge levels (e. g. full and half-full batteries/
rechargeable batteries).
• Always replace the complete set of batteries/rechargeable batteries.
• Check that the polarity is correct, when inserting the batteries/rechargeable batteries (pay attention to
plus/+ and minus/-).
Preparations for Installation
If the door where you want to install the peephole monitor already has a conventional peephole, it is usually
very easy to replace the old peephole with the new one.
If the door does not have a peephole, you have to install the peephole enclosed. Therefore, you have to drill
a matching hole in the door.
☞
www.conrad.com
Version 10/13
Controls
1 Clamp screw
2 Slot for microSD memory card
3 LED for "Flat battery"
4 Power key
5 Switch to change brightness
6 Key "S"
7 Key "F"
8 Battery compartment cover
Getting Started and Installation
• Open the battery compartment cover, on the back of the peephole monitor.
• Insert two batteries type AA/Mignon paying attention to the correct polarity into the battery compartment
(observe the illustration in the battery compartment).
• Close the battery compartment.
• Unscrew the peephole sleeve from the peephole lens.
• Replace the old peephole in your door with the new one.
☞
Insert the peephole lens into the hole from the outside of the door. Place the plastic retainer on the inside
of the door and screw it tightly onto the peephole sleeve on the lens.
When you use a 12 mm peephole, you have to attach the supplied washer so the plastic retainer can be
attached.
• Screw the peephole sleeve fi rmly into place, using the enclosed installation spanner.
Please pay attention so the labelling "STOP" on the plastic retainer points upwards.
• Finally, attach the peephole monitor to the plastic retainer. By rotating the peephole monitor to the right, it
will lock on to the plastic retainer.
☞
Inserting/Removing the Memory Card
You can insert a memory card on the left side of the peephole monitor in order to save pictures of the visitors.
For this, you need either a microSD memory card (max. 2GByte) or a microSDHC memory card (max.
32GByte). A memory card is not included, but one can be ordered separately.
If you want to remove the memory card, please wait until the peephole monitor is turned off. Only then extract
the memory card. Otherwise, data may be lost or the data system damaged. It may then be necessary to
reformat the memory card on your computer.
Setting the date and time
When pictures are saved, each picture is marked with the date and time it was taken.
To set date and time, proceed as follows:
• Turn on the peephole monitor, by pressing the Power key for about 1 second, so the picture appears on
the monitor.
• Press the key "S" on the side for about 2 seconds and the date and time will be
shown on the display.
• Using the keys "S" and "F" you can choose between "Set" (Activate set mode)
or "Exit" (Exit set mode).
Press the Power key for confi rmation.
• When you have activated the set mode, the year blinks on the display. Set the
year using the keys "S" and "F".
• Press the Power key, the setting is confi rmed and you are now able to set month,
date, hour, minute and second, one after the other.
After setting the seconds and pressing the Power key, the display will show
"Done". Press the Power key again in order to exit the set mode. The camera's
picture reappears.
If you live in a rented apartment, please ask your landlord for permission fi rst. Some landlords
will drill the hole in the door and install the peephole monitor for their tenants.
If you install the peephole monitor without consulting your landlord fi rst, you may have to under-
take the costs for restoring the door or sacrifi ce part of the deposit when you move.
When there is no peephole, drill a suitable hole in the desired spot on the door (diameter 14 mm
or 12 mm, according to the supplied peephole, see the peephole's packing) For correct installa-
tion, the door should be between 40 mm and 69 mm thick)
If you want to screw on the peephole monitor, you can tighten the screw on the left side (see the
illustration in the chapter "Controls", Position 1).