Declaration Of Conformity; Mounting And Operation - Bosch AGS Originalbetriebsanleitung

OBJ_BUCH-1077-006.book Page 13 Thursday, December 12, 2013 11:59 AM
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

Grass Shear
We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
(battery powered product) and EN 60335 (battery charger)
according to the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC, 2011/65/EU.
Shrub Shear
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
(battery powered product) and EN 60335 (battery charger)
according to the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU.
2000/14/EC: Guaranteed sound power level 77 dB(A). Con-
formity assessment procedure according to Annex V.
Equipment category: 25
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS23,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
12.12.2013
Bosch Power Tools

Mounting and Operation

Action
Delivery Scope
Battery Charging
Detaching Tool
Attaching Tool
Switching On and Off
Fitting Telescopic handle
Adjusting Handle Length
Setting for Edge Cutting
Maintenance
Accessories
Anti Blocking
The garden product has a patented feature which works as
follows:
If the blade stalls on a tough material, the load of the motor in-
creases. The intelligent micro-electronics senses this over-
load condition and repeatedly reverses the motor, in order to
prevent stalling and to cut the material through.
This audible reversing cut action continues for up to 3 s.
After cutting through, the garden product continues in its nor-
mal mode, or in case the overload condition continues the
blades automatically stop in the open position (e. g. in case a
piece of metal fence accidentally blocks the garden product).
Battery Charge-control Indication
The battery charge-control indicator indicates the charging
progress. During the charging process, the indicator flashes
green. When the battery charge-control indicator lights up
green continuously, the battery is fully charged.
The battery charge-control indicator indicates the charge
condition of the battery for a few seconds when the On/Off
switch is pressed through halfway of fully.
LED
Continuous lighting, green
Flashing light, green
Flashing light, red
Continuous lighting, red
English | 13
Figure
1
2
3
4
5
6
7
8
9
10
Capacity
35 – 100%
15 – 35%
5 – 15%
0 – 5%
F 016 L70 969 | (12.12.13)