Technical Data; Noise/Vibration Information; Declaration Of Conformity; Mounting And Operation - Bosch AHS 45-16 Originalbetriebsanleitung

OBJ_BUCH-1297-002.book Page 10 Friday, October 8, 2010 11:34 AM
10 | English

Technical Data

Hedgecutter
Article number
Rated power input
Cutting length
Tooth opening
No-load stroke rate
Weight according to EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual
garden products may vary.

Noise/Vibration Information

Measured sound values determined according to
2000/14/EC.
Typically the A-weighted noise levels of the product
are: Sound pressure level 84 dB(A); sound power level
95 dB(A). Uncertainty K =2 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration emission value a <2.5 m/s
h
2
K =1.5 m/s .
The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure lev-
el over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the op-
erator from the effects of vibration such as: maintain
the tool and the accessories, keep the hands warm, or-
ganisation of work patterns.
Troubleshooting
Problem Possible Cause
Hedgecutter does not Power turned off
operate
Mains socket faulty
Extension cable damaged
Fuse faulty/blown
Hedgecutter operates Extension cable damaged
intermittently
Internal wiring of garden product damaged Contact Service Agent
On/Off switch defective
Motor runs but blades Internal fault
remain stationary
Cutting blade hot Cutting blade blunt
Cutting blade has dents
Too much friction, due to lack of lubricant Apply lubricant spray
Excessive vibrations/ Garden product defective
noise
F 016 L70 775 | (8.10.10)
AHS 45-16
3 600 ... H47 A..
W 420
mm 450
mm 16
-1
min 3400
kg 2.6
II
/

Declaration of Conformity

We declare under our sole responsibility that the prod-
uct described under "Technical data" is in conformity
with the following standards or standardization docu-
ments: EN 60745 according to the provisions of the di-
rectives 2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 97 dB(A).
Conformity assessment procedure according to
Annex V.
Equipment category: 25
2
, Uncertainty
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
08.10.2010

Mounting and Operation

Action
Delivery Scope
Connecting the Extension Lead
Starting
Stopping
Working Advice
Blade Maintenance
Storage and Transport
Selecting Accessories
AHS 50-16 AHS 55-16 AHS 60-16
H47 B.. H47 C..
450 450
500 550
16 16
3400 3400
2.7 2.7
II II
/ /
Dr. Eckerhard Strötgen
Head of Product
Certification
Corrective Action
Turn power on
Use another socket
Inspect cable, replace if damaged
Replace fuse
Inspect cable, replace if damaged
Contact Service Agent
Contact Service Agent
Have blade sharpened
Have blade inspected/overhauled
Contact Service Agent
Bosch Power Tools
H47 D..
450
600
16
3400
2.8
II
/
Figure
1
2
2
2
2, 3
4
4
5