Herunterladen Inhalt Inhalt Diese Seite drucken

Troubleshooting - Clarion EE-2179E Installations- Und Bedienungsanleitung

Drahtloses digitalkamerasystem
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

HOW TO INSTALL
I How to attach the monitor with receiver
1
Place the arm part of the monitor
Monitor mounting part
stand in an upright position.
Face the mounting part forward.
2
Rotate the threaded portion of
the antenna clockwise and fix the
(short) antenna securely to the
monitor to prevent loosening.
3
Slide the monitor mounting part of
the monitor stand into the groove in
the back of the monitor.
4
Tighten the monitor height
Monitor height adjusting screw
adjusting screw in the back of the
monitor stand with the supplied
hexagonal wrench (3 mm) and fix
the monitor securely.
5
Adjust the angle of the monitor and
tighten the monitor angle adjusting
screw on the side with the supplied
hexagonal wrench (3 mm).
Monitor angle adjusting screw
6
Decide the position for mounting the monitor stand.
7
Wipe the mounting surface (dashboard, etc.) clean, remove the
protective tape from the bottom of the stand and press the stand
onto the surface to attach it securely.
8
Fix the monitor stand securely
4Self tapping screws (5 places)
with the supplied self tapping
screws (5 places).
9
Adjust the monitor to the
optimum viewing angle
and tighten the adjusting
screw to fix securely.
Monitor angle adjusting screw
Stand angle adjusting screw
I How to mount the camera with transmitter
CAUTION
G Never swing the camera by the cable or pull the cable. Doing so may
impair the camera's watertightness or break the cable, resulting in
malfunction.
G Avoid mounting the camera where the lens will be exposed to dirt (mud
splashes, exhaust fumes, etc.).
G To prevent the camera from shaking, make sure the camera is mounted
to solid surface. The surface may need reinforcement if it is not solid
and secure.
G Be sure to use the supplied screws to mount the camera. If any
screws are lost when mounting the camera, be sure to use hexagon
head bolts with built-in washer (M3 mm x 8 mm). Do not under any
circumstances use screws longer than this. To ensure watertightness,
the screw mounting holes in the camera case have a bag structure.
Use of long screws may damage the screw thread and camera case,
compromising watertightness.
Antenna
(Short)
1
Make a hole (2 places) for mounting the bracket in the chassis and
fix the bracket securely with the @ hexagon head bolts with built-in
washer and flanged nuts.
2
Push-fit the gasket boss (2 places) into the guide hole from inside
the bracket.
3
Temporarily fix the camera in 4 places (a) with the ! hexagon
head bolts with built-in washer.
4
Using tools such as needle nose pliers, rotate the threaded
portion of the antenna clockwise and fix the (long) antenna securely
to the camera to prevent loosening.
5
Temporarily fix the antenna bracket in 1 place (b) with the !
hexagon head bolt with built-in washer so that the angle of the
antenna is controlled.
6
Install the wiring. (Refer to WIRING AND CONNECTIONS)
7
Adjust the mounting angle of the camera so that the rear bumper or
back end of the vehicle appears in the monitor and tighten the bolts
(a) to fix securely. (See diagram below)
Monitor screen
The recommended guideline is approximately
1/10 of the monitor's overall height.
Rear bumper or rear end of the vehicle
8
Adjust the antenna angle for optimal signal reception and tighten
the bolt (b) to fix securely.
0 Gaskets (Two places)
$ Antenna bracket
!
Hexagon head bolts
with built-in washer (a)
(M3 mm x 8 mm)
(Four places)
Boss
(a)
(a)
Boss
(a)
(a)
(b)
Threaded portion
of the antenna
Guide holes
!
Hexagon head bolt
with built-in washer (b)
(M3 mm x 8 mm)
(One place)
8
Mounting bracket
@ Hexagon head bolts with built-in washer
(M5 mm x 8 mm) (Two places)
Vehicle side: 5.5 mm holes (Two places)
# Flanged nuts (M5 mm) (Two places)
PAIRING
The camera and monitor have been paired at the factory, so pairing is not
required at the initial installation stage. The pairing steps can be skipped in
this case.
If the camera or monitor are replaced for any reason, then pairing must be
completed as per the instructions below. Pairing is also required each time
you change Tractor/Trailer combinations.
Precautions for uses
Precautions for uses
• If there are multiple connectable cameras, before pairing, turn
on only the camera you want to connect and turn off any other
cameras.
If pairing is performed when there are multiple connectable
cameras, the paired device will be selected automatically and it may
not be the camera that you want to connect.
1
Press the pairing button (on the rear
of the monitor) for four seconds.
2
The words "please Press Pair Key
on Camera Side" will appear on
the monitor. A 30 second timer
will then count down. Please pair
before 30 seconds elapses.
3
Pairing method
Pairing method depends on vehicle type and design of vehicle
wiring harness.
(+) Reverse or Parking
light Line of Camera
(1): Connect to reverse
line (If the tractor/
trailer combination
is changed,
reconnection of the
pairing signal cable is
not required)
(2): Connect to
illumination line
9 Antenna (Long)
© The camera video will appear on the monitor and pairing is
complete.
Wiring Precaution
Wiring Precaution
• Please carry out waterproof treatment on hookup point between
camera power cable and vehicle wiring as per the illustration below.
The end of
camera power cable
As well as wire connections, please do waterproof to the end of
camera power cable.
WIRING AND CONNECTIONS
G Do not connect the power cable (red) of either the transmitter or the
receiver to the +B line (permanent power supply) as this may lead to a
flat battery.
G Disconnect the negative terminal of the battery
before connecting the cables. Failure to do so
may lead to electric shock or injury due to short-
circuit. It may also lead to damage to the system
components due to short-circuit.
Precautions when connecting the cables
Precautions when connecting the cables
• To prevent short-circuiting, check the connections again before
connecting the battery.
Monitor with receiver
Pairing button
Black
ACC+
Connect to a positive power
supply that can be turned on
and off with the ignition key.
Pairing Method
Ground (Negative)
Connect to chassis ground.
Connect the pairing signal cable (brown)
to the illumination line of the vehicle.
1 Turn off the illumination.
2 Put the reverse gear into reverse.
MONITOR SETUP
3 Turn on the illumination for at least 1
second. ¡ Pairing starts
I MENU
4 Turn off the illumination and return the
reverse gear to its original position.
©To repeat pairing, repeat steps 1 to
Menu Screen Display
4.
Input Mode
1 Connect the pairing signal cable
Setting
(brown) to the illumination line to which
a positive power source is supplied for
Color
at least 1 second. ¡ Pairing starts.
Adjustment
2 When pairing is completed,
disconnect the pairing signal cable
(brown) and insulate with insulating
tape to prevent malfunction or short-
circuiting.
System
Information

TROUBLESHOOTING

Camera power cable
The following situations may not be malfunctions, please check prior to
Vehicle wiring
requesting service.
Symptom
Waterproof
Waterproof
There is no image (Nothing
appears on the monitor)
There is no image ("No
Signal" is continuously
displayed on the monitor)
Wire connections
The image cuts out
CAUTION
Camera
with transmitter
Red
Brown
Black
Red
(+) Reverse or Parking light
Please refer to the item 3. of PAIRING
section.
Ground (Negative)
Connect to chassis ground.
Pairing
Only used for pairing. Refer to PAIRING
section for the pairing procedure.
Sub Screen
Display Description
Display
Input (Switch External
Switchover to external input not supported.
Input)
(Only CCD is displayed)
Information
Displays manufacture information.
Contrast
For adjusting contrast.
Brightness
For adjusting brightness.
Saturation
For adjusting color saturation.
Hue
For adjusting color hue.
Sharpness
For adjusting sharpness.
Sleep Timer
Timer function not available.
Although numbers can be changed, please leave
the setting at "0".
Language
For setting language. Available languages are
English, French, German, Spanish and Korean.
Reset
Reset all menu screen settings to default
settings.
Cause
Measure
The connection of the monitor is
Check the connection of the monitor
not correct.
and connect correctly
The connection of the camera is
Check the connection of the camera
not correct.
and connect correctly
The surrounding radio wave signal
Move to a different place and check if
strength is weak
the image appears
The surrounding radio wave signal
Move to a different place and check if
strength is weak
the image appears

Werbung

Inhaltsverzeichnis
loading

Verwandte Produkte für Clarion EE-2179E

Inhaltsverzeichnis