Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Overview of the Components
1 Refill opening cap / measuring cup
2 Mixing vessel lid with refill opening
3 Mixing vessel
4 Seal ring
5 Knife block
6 Base section with motor
7 Setting switch
Installation
Mixing vessel
1. Place the mixing vessel onto the motor housing. Follow the
symbols on the housing. Position the mixing vessel so that
the handle lies above the symbol.
2. Secure the mixing vessel by turning it clockwise.
NOTE:
The mixer will not operate if assembled incorrectly.
Lid
1. Check that the seal ring is secure on the lid.
2. Press the lid firmly onto the mixing vessel. It must seal the
mixing vessel completely.
3. Insert the cap into the refill opening of the lid. Use the sym-
bols on the cap and the markings on the lid. Secure the cap
by turning it clockwise. The symbol must lie next to .
NOTE:
The refill opening cap can also be used as a measuring cup.
Instructions for Use
CAUTION:
The glass may crack if the temperature is too high! DO not fill
with liquids above 60°C.
•
Place the device on a firm and flat surface. Position it is
such that it cannot tip over.
•
Only switch on the appliance if the mixing vessel is closed
with the lid. The refill opening in the lid must also be closed.
•
Do not overfill the mixing vessel! You can fill it to a maxi-
mum of 1.5 liters. Use the scale on the jug.
•
Froth requires a large capacity. Reduce quantities of liquids
which produce a lot of froth.
•
Keep one hand on the lid if you are crushing ice or if there
is a large quantity of ingredients.
•
Cut the food to be mixed into small pieces beforehand.
Electric Connection
•
Before inserting the power plug into the outlet, check that the
mains voltage to be used matches that of the device. You
can find the required information on the nameplate.
•
Connect the device only to a correctly installed safety socket.
32
Short-interval use
The appliance is suitable for short-interval use of a maximum of
2 minutes. Allow it to cool for 2 minutes before using it again!
Pulse mode
Switch to pulse mode by turning the control to the "P" position
and then release it. Use the appliance in this operating mode
for a maximum of 2 minutes. Allow it to cool for 2 minutes
before using it again!
Crushing ice cubes:
The blades in the mixing vessel are also suitable for crushing
ice cubes.
•
Put a maximum of 10 pieces (size approx. 25x25x25 mm)
into the mixing vessel.
•
Use pulse operation "P" for 1 - 3 seconds. Repeat the
process 8 - 12 times.
•
When adding fluid, you can use the "2" setting for
1 - 2 minutes.
Operation
Preparation
1. Ensure that the function switch is in the "0" position.
2. Place the mixing vessel in position.
3. Now put the ingredients that are to be mixed into the mixing
vessel.
4. Put the lid on.
5. Close the refill opening with the cap.
Mixing
Operation is carried out with the setting control:
Level 0
=
off
Level 1
=
low rpm
Level 2
=
high rpm
P
=
High speed in pulse mode
Adding further ingredients to be mixed
Items to be mixed or spices can be fed in through the filling
aperture.
•
Please switch off the machine before doing so.
•
Before you switch the device on again, close the opening.
Stopping Operation
1. Turn the switch to the "0" position.
2. Wait until the blade comes to a complete stop.
3. Remove the mains plug from the socket.
4. Remove the mixing vessel. Turn it anticlockwise.
5. Take off the lid before pouring.
IMPORTANT NOTE:
Citrus juices and food containing acids should never be
stored in metal vessels.
Werbung
Inhaltsverzeichnis
