Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL HT 2000 Originalbetriebsanleitung

and blows out air without heat output. To switch
off , press the "ON/OFF" button again. The fan
continues to run for a while after the equipment
has been switched off .
6.3 Setting the heat outputs (Fig. 5)
With the heater switched on, press the "Mode"
button (K). The equipment will heat with 1200 W. If
you press the "Mode" button again, the equipment
will heat with 2000 W. The display will show either
"1200" or "2000" depending on the heat output
setting. Press the "Mode" button again and the fan
will continue running without any heat output.
6.4 Setting the operating times (Fig. 5)
With the equipment switched on, press the „Ti-
mer" button (L). Each time you press this button
the set operating time increases by 0.5 h within a
time frame of 0.5 - 7.5 h. The set time will appear
in the display in combinations of 0:30, 1:00, 2:00
and 4:00 (e.g. for 4.5 h, the combination is 4:00
+ 0:30).
6.5 Switching the oscillation function on/off
(Fig. 5)
Press the "Swing" pushbutton (M). The equipment
will swivel approx. 35° to the left and 35° to the
right. To switch off the "Oscillation" function and
have the equipment blow in one specifi c direction
only, press the "Swing" pushbutton again.
6.6 Topple cut-out
This will trip as soon as the equipment is tipped
beyond a certain angle. You can continue using
the equipment as described above after you have
returned to its upright position. The integrated
topple cut-out makes a noise that can be heard if
the equipment tilts. This is not a fault.
6.7 Overheating guard
In case of excessive heating, the heat output or
the equipment will shut down automatically. In this
case switch off the equipment completely and un-
plug it from the mains power. Allow the appliance
to cool for about 15 minutes. After eliminating the
cause (e.g. a covered air grille), the equipment
can be switched on again as described above. If
the overheating guard triggers repeatedly or the
equipment cannot be switched on, please contact
your customer services workshop.
Anl_TH_2000_SPK1.indb 18 Anl_TH_2000_SPK1.indb 18
GB

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
The equipment must have cooled down.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
Remove dust with a vacuum cleaner.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
- 18 -
23.01.2017 12:53:34 23.01.2017 12:53:34