Werbung
EN
1. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE ASSEMBLING YOUR GREENHOUSE.
2. Sharp edges and corners can cause injury. Always wear protective glasses, gloves, shoes and headgear when handling the aluminium profiles, glass
and polycarbonate sheets. Broken glass is a safety hazard – always clear up immediately and dispose of with care.
3. The product you have purchased is intended only for the growing of plants and should only be used for this purpose. When used for other purposes we
will take no responsibility.
4. It is recommended that this greenhouse is assembled by two people.
5. When using a step ladder one person should steady it at all times whilst the other works.
6. Should you encounter difficulties constructing this house or in positioning the polycarbonate sheets, please contact your retailer
– do not use force!
7. The green house must always be anchored.
SIte SelectIoN
Always try to select a sunny location, sheltered
from the wind as much as possible.
ImPoRtaNt
Before assembling your new greenhouse,
please check that all parts in the provided list
are included. Please take each bundle out of
the packaging in order to identify the parts
better.
It is important that the opened bundles do not
get mixed with one another.
If something is missing please contact your
retailer.
Note - The UV-resistant side of the polycar-
bonate sheets is indicated by a plastic film
or printing at the edge. this side must face
outside.
In order to seal the greenhouse effectively it is
suggested that you apply neutral silicone as
shown in diagrams (4b.4), (4b.5), (7a.7) and
(7a.9). Silicone is provided for this purpose.
NeceSSaRy toolS
Screw drivers (Normal and Crosshead PH2)
Rubber Hammer
2 x 1.8m ladder
10 mm socket spanner or wrench
10 mm combination spanner
Craft knife
Measuring stick
Spirit level
Accu-drill with adjustable torque
maINteNaNce
The greenhouse should be thoroughly washed
with a gentle detergent occasionally. Please
check that the detergent used does not react
aggressively with aluminium or plastic.
Ensure that the door tracks are cleaned regu-
6
Safety Warning
Assembly Instructions
larly to avoid a build up of debris.
0. FouNdatIoN
Important! The foundation must be exactly
right angular and level. To achieve this you will
require a spirit level and a right angle.
Note - If the distance between the two opposi-
te corners is the same then the foundation is
right angular.
For the erection of this greenhouse we
suggest a solid foundation constructed from
concrete, brickwork or stonework.
If you have no experience with the construc-
tion of such a foundation please consult a
company specialising in this work.
Materials and tools for the preparation of the
suggested foundation are not provided.
The suggested foundation allows the door to
be assembled on any side of the greenhouse.
Foundations must extend down below the frost
level.
diagrams in a single frame show the view
from inside the greenhouse. those enclo-
sed in a double frame show the view from
outside the greenhouse.
1. FRoNt elemeNtS
Note - If the door is to be assembled in the
front of the house remove one of the middle
bars (7311).
Push silicon seal (7396) into the sill bar (7304
- 7307) and cut to fit both ends (1.1) (1.2).
Lay all of the parts, according to the model, on
the floor and loosely connect by inserting bolts
(7052) into the bolt channels.
Take care that the eave angles (7314 - 7317)
are pushed into the corner of both corner bars
(7310) (1.3) (1.4) and that corner bars (7310)
and middle bars (7311) sit correctly on the
assembly edge on the eave angle (1.9) (1.12).
Assemble diagonal bars (7312) on both sides
(1.3) (1.4) (1.10) (1.11). At the sill loosely
attach temporary bolt (7050). (7050) will be
removed during glazing (section 7b).
2. PlaIN gable eNd
Note - If the door is to be assembled on this
side of the house remove middle bar (7311).
Push silicon seal (7396) into sill bar (7301)
and wall bar (7344) and cut to fit the ends
(2.1) - (2.4).
Lay all of the parts on the floor and loosely
connect by inserting bolts (7052) into the bolt
channels.
Assemble end bar (7321) into the recess in
wall bar (7344) (2.5) (2.6) and then (7344)
onto sill bar (7301) (2.7) (2.8).
Assemble middle bars (7311) (2.9) (2.10),
noting the assembly edge on the eave angle
(1.9).
Assemble diagonal bar (7313) (2.5) (2.11)
(2.12). At the sill loosely attach temporary bolt
(7050). (7050) will be removed during glazing
(section 7b).
3. dooR gable eNd
Note - If the door is to be assembled on ano-
ther side then assemble the (7311), which
was previously removed, in position b.
Assemble all parts as in Section 2.
4a. coNNectINg the SIde elemeNtS
(4a.1) shows the 4a assembly if the door is to
be in the front of the house.
Push silicon seal (7396) into the ridge bar
(7334 - 7337) and cut to fit the ends. Check
that ridge seal (7414 - 7417) is correctly
inserted into the guide in the ridge bar. (4a.2)
(4a.3).
036.01.1512
Werbung
