Herunterladen Diese Seite drucken

Vitavia HELENA 2 Montageanleitung Seite 7

Werbung

Loosely prepare bolts (7052) and nuts (7053)
in sill bars (7301) and (7302) as shown in
(4a.4). Lower corner bars (7310) fitting the
bolt heads of (7052) into the bolt channels of
(7310) (4a.5).
Connect end bars (7321) and (7322) to corner
bars (7310) ensuring they are pushed against
the eave angle bar (4a.6).
Assemble roof corner bars onto the eave
angle (4a.7) (4a.8). Ensure that the roof corner
bars sit correctly on the assembly edge on the
eave angle (4b.6) and that the small holes on
the outside of (7428 / 7429) are at the eave
end (4a.7).
Assemble the ridge bar (7334 - 7337), roof
corner bars (7428) (7429) and wall bars (7344)
(7345) (4a.9) (4a.10) using plate (7348).
Note: Ensure the ridge seal (7414 - 7417)
is bent forward over the roof corner bars
(4a.10).
Assemble end middle bars (7346) (7347) to
the end bars and the roof corner bars using
plate (7348) (4a.11).
Position the assembled frame against the wall
on the prepared foundation, check that it is
level and drill ø6 holes through the prepared
holes in (7301), (7302), (7304 - 7305), (7344)
and (7345) on the wall and foundation.
Insert wall plugs (7421) or (7422) into the ho-
les and connect loosely to the foundation and
wall using screws (7411) and (7412) (4a.12).
4b. RooF mIddle baRS
Loosely prepare (7052) and (7053) in the ridge
bar and slide middle bars (7472) into position
fitting the bolt heads of (7052) into the bolt
channels of (7472) (4b.1) (4b.2).
Note: Ensure the ridge seal (7414 - 7417) is
bent forward over the roof middle bars (7472)
(4b.3).
Insert (7052) into the bolt channel in (7472) at
the eave and lower onto the eave angle using
washer seal (7395) and nut (7053) (4b.4)
(4b.5). Ensure that (7472) sit correctly on the
assembly edge on the eave angle (4b.6) and
that the small hole on the outside of (7472) is
at the eave end (4b.7).
Drill ø6 holes through the prepared holes in
(7334 - 7337). Insert wall plugs (7422) into the
holes and loosely connect the ridge bar to the
wall using screws (7412) (4b.8).
Adjust the frame until it is completely right
angular and tighten all screws (7411) and
(7412) and nuts (7053). Please do not over
tighten.
Assemble corner braces (7331) between each
side middle bar (7311) and roof middle bar
(7472) by inserting cropped head bolts (7399)
into the bolt channels (4b.9) (4b.10).
5. SIde wINdow
Connect window bottom bar (7451) to side
036.01.1512
bars (7453) and (7454) (5.2) (5.3).
Slide pane D into the glazing channels (5.5) in
the assembled parts (5.4) (5.5).
Loosely prepare (7052) and (7053) in window
top bar (7450) and slide onto (7453) and
(7454) fitting the bolt heads of (7052) into the
bolt channels and the glazing into the glazing
channels (5.6) (5.7).
Note - If you have chosen 4mm glass glazing,
cut glazing seal (7420) to fit and press into the
space in the glazing channels on the inside of
the window to fix the glass in place (5.8) (5.9).
Check that the side window is right angular
before tightening all bolts.
Please do not over tighten.
Insert brush seal (7457) using 1 continuous
length into the guides in the top and side bars
(7454) (7450) (7453) (5.10) and cut to length.
Note - If the brush seal (7457) protrudes along
the top edge of (7450) when the window is
closed, (see section 8), it can be trimmed
shorter (5.10).
Connect window opener (7090) to (7451)
using spacer (7413) and two screws (7349)
(5.11) (5.12).
Connect plastic nut caps (6070) by pushing
them onto all nuts (7053) (5.13).
6a. SlIdINg dooRS
Insert brush seal (7332) into the guides in the
door bars (7352) (7353) (7355) (7356) (7357).
(6a.2) and cut to length.
Loosely assemble wheels (7364), using
spacers (7392) on each side of the wheel, bolt
(7393), jump clip (7350) and lock nut (7360),
onto door bottom bars (7355) (6a.3).
Connect (7355) with door side bars (7357) or
(7358) (6a.3) (6a.7a).
Assemble door middle bars (7354) or (7384)
with lock parts (7400), (7401) and (7402) using
bolts (7404). Connect to door side bars (7357)
or (7358) using bolts (7052), nuts (7053) and
bolts (7405) (6a.4) (6a.5) (6a.8). do not over
tighten bolts (7404) and (7405).
Connect door top bars (7352) or (7353) to
door side bars (7357) or (7358) (6a.6) (6a.7b).
Slide panes G into the glazing channels in the
assembled parts (6a.9).
Loosely prepare (7052) and (7053) in door
side bars (7356) and slide onto (7355), (7354)
or (7384) and (7352) or (7353) fitting the bolt
heads of (7052) into the bolt channels and
the glazing into the glazing channels (6a.9)
(6a.10). Insert door guides (2271) into the top
of both doors (6a.6).
Note - If you have chosen 4mm glass glazing,
cut glazing seal (7420) to fit and press into the
space in the glazing channels on the inside of
the door to fix the glass in place (6a.11).
6b. dooR FRame aNd SteP
Assemble door support (7362) onto the sill bar
in the door opening using bolts (7390) (6b.1)
(6b.2).
Tilt door wheel track (7351) to fit into the sill
bar and lower into position (6b.3). Centre on
the door opening and connect to the founda-
tion using wall plug (2003) and screw (2002)
(6b.4).
Connect door side frames (7361) to middle
bars (7311). When in place connect to the
top using bolt (7052) and nut (7053) (6b.5) -
(6b.8).
At the bottom insert bolt (7052) into the chan-
nel on both sides of door step (7363) (6b.9)
and slide the door step into place (6b.10)
(6b.11).
7. glazINg oveRvIew
Please sort the glazing according to your
model size and glazing type before beginning.
If you have chosen glass then panes E and F
are identical on both sides.
Note - The UV-resistant side of the polycar-
bonate sheets is indicated by a plastic film
or printing at the edge. this side must face
outside. Loosen the film approximately 2cm
at all edges of each pane before assembly.
When the assembly of all sheets is finished
completely remove all film from the sheets.
7a. RooF glazINg / eave
Slide the roof glazing into the guides in the
roof profiles (7a.2) (7a.3). When two adjacent
sheets are in place, screw glazing stops
(7342) or (7343) onto the roof profile between
them using the prepared holes and self-drilling
screws (7349) (7a.4) (7a.5). The sheets should
slide down to rest against these stops.
Note: Ensure the ridge seal (7414 - 7417) is
bent forward over the roof sheets B (7a.6).
Angle the eave bar (7324 - 7327) into the eave
angle (7a.7) and turn it down to rest against
the eave angle. Connect it to the eave angle
using bolts (7052) from outside and nuts
(7053) inside the house (7a.8).
Insert glazing spacer (7424) over the inside
edge of the eave angle (7a.9) and glazing
spacer (7425) over the inside edge of the ridge
bar (7a.10). At the ridge fix (7425) in place
using screw (7349) (7a.10).
Note: The formation of condensation is una-
7

Werbung

loading

Diese Anleitung auch für:

700086001020011900Athene 2